manualshive.com logo in svg

Fujitec VIS SETTER MK-3020, Инструкция по эксплуатации

Поделиться
Скачать
Fujitec VIS SETTER MK-3020 Скачать руководство пользователя страница 20

１２．Troubleshooting

If problems should occur, then use the following chart to find and eliminate it.Consult your dealer
if the following troubleshooting chart does not correct the problem. (Always consult the dealer in
cases where a ※ mark appears below.) Inadequate or incomplete troubleshooting will not only
hurt machine performance but may also create hazardous situation.

Symptom

Cause

Action

Page

Rotary drum fails
torotate or stops
abnormally

Power switch not 
turned on

Turn on power switch.

Fuse(3A)on control board is 
blown. Replace it.

The optical axis of the optical
switch has deviated. Adjust the
optical axis.

Clean the screw sliding sections
along the chute

Remove the screws and clean

the interior of the hopper,
reverse the rotating drum back
slightly by hand, and remove the 
screws

Adjust the driver roller
transmission force

Consult your dealer, and request
assistance

The optical axis of the optical
switch has deviated.Adjust the 
optical axis

Adjust the impeller vane height

Clean the interior of the hopper.
Drive ( transmitting) force is low
because the torsion spring has
weakened. 

※

Replace the

torsion spring

Power lamp won't light 
up

Motor lamp won't light 
up

Screws have stopped
along sliding surfaces
of chute

Screws  are binding
between rotating
drum's scoop pawl and
the hopper

Driver roller
transmission force is
weak,causing slipping

Motor won't turn

Motor lamp won't light
up

Impeller vane is
binding on head plate

Impeller is slipping

Rotating drum won't
stop even if screws are
lined up in chute

Impeller vane won't rotate

１１

１５

１４

１２

１２

１３

１４

※

１４

Remove the screws that are
binding, recheck the impeller
height, and readjust it

Screw are binding on 
impeller vane

１３

１２

- 20 -

Содержание VIS SETTER MK-3020
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды