manualshive.com logo in svg

Fujitec VIS SETTER MK-3020, Инструкция по эксплуатации

Поделиться
Скачать
Fujitec VIS SETTER MK-3020 Скачать руководство пользователя страница 13

７．Maintenance and storage

7-1．Maintenance  after daily work

Always turn off the power switch before cleaning or
servicing the unit. Unplug the power cord from the outlet
(socket) if not planning to use it for a long time.

① Cleaning the chute

Use a brush or similar tool to clean dust or 
metal powder that is sticking to the screw 
sliding surfaces of the chute.
Gently wipe away oil using new cloth moistened with
alcohol.Take care not to scratch or dent the sliding 
surfaces during cleaning. 

② Supplying oil and draining  water from 
     the filter

If using the VIS SETTER Handy as an air screwdriver,
loosen the needle valve on the oiler and check
from the droplet window that 3 to 5 drops of oil
fall while operating the air screwdriver under no load
(run with no load on the tip).
Then tighten the needle valve. Finally operate the air
screwdriver under no load for 1 to 2 minutes.

Loosen the drain cock and let water from inside 
the tank drain off. Do not let water accumulate
above the upper limit line in the drain window.

7-2．Once a week maintenance

① Cleaning the inside of the hopper

Take out the screws from inside the hopper and 
remove debris.
If extremely dirty or oil is adhering, wipe away gently 
with a fresh cloth moistened with alcohol.
Do not use anything other than alcohol.

② Checking the oil level in the oiler.

If using the VIS SETTER Handy as an air screwdriver, 
check whether the oil level in the oiler is within
the upper and lower limits. If the oil level is low,
shut off the air source (compressor, etc.),
remove the oil fill plug,and fill with oil.
You should use turbine oil (class 1) ISO-VG32.

Note：Do not use spindle oil or machine oil.
　

Brush

New cloth

Oil supply plug

Top
mark

Bottom
mark

Oiler

上限

D

ro

pl

et

wi

nd

o

w

Top
mark

Drain 
cock

Tighten

Loosen

Open

Needle valve

Close

- 13 -

Содержание VIS SETTER MK-3020
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды