manualshive.com logo in svg

Fujitec VIS SETTER MK-3020, Инструкция по эксплуатации

Поделиться
Скачать
Fujitec VIS SETTER MK-3020 Скачать руководство пользователя страница 10

５．Pre-operating setup

5-1．How to install

1) Install at a position 200 to 250 mm higher than the

location where the screws are supplied and 
be careful not to twist or forcibly bend
the feed hose.

2) Prepare a stand block for use during installation

and set so that the rubber feet of the feeder unit 
are on the stand  block.
Installing directly without using a stand block will 
cause a drastic bend in the screw feed hose.

5-2．Installing the wiring and piping

Always connect to ground line. Failure to connect
to ground may cause elecrical shocks.

1) Connect the ground terminal on the rear panel to
  ground by using a ground wire.

2) Then connect power supply cord to a powers  supply.

3)Connect the air hose to the factory air source.

(or air compressor.)
The air hose fitting is the φ8
The source air pressure cannot be adjusted on this
unit,so adjust the factory source air pressure to a
range wihtin 0.4 to 0.5 MPa.

4) If using  the air screwdriver,connect the air

screwdriver hose to the φ8 fitting 
on the front panel of the feeder.

5) Connect the screw feed signal plug (from external

 section) to the receptacle (3P) on the front panel of
the feeder.

6) Install the screw feed hose on to the escapement.

CAUTION

Rubber feet

Stand

Ground

AC outlet

Factory
air 

0.4

～

0.5MPa

When using air driver

screw 

screw feed 
hose

0.4

～

0.5MPa

Factory air
source

When using air driver

AC  outlet

Ground

- 10 -

Содержание VIS SETTER MK-3020
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды