4.2 Single Display Unit
(8) Shift key
Pressing the Shift and Enter keys
together changes to the parameter
checking mode. (Comparator data
can be set.)
Pressing the Shift and Mode keys
together changes to the shift function
setup mode.
Selects from items in the maximum/
minimum/(maximum-minimum)/input
value monitoring mode. (Hold down
the key for about one second.)
Changes the digit to be set.
Holding down the Shift key for about
one second moves to the HI judgment
value indicator.
Increment key
(9)
Pressing the Increment and Mode
keys together turns on/off the "Digital
zero" indicator.
Pressing the Increment and Enter
keys changes to the maximum/
minimum/(maximum-minimum)/input
value monitoring mode.
Resets the maximum/minimum/
(maximum-minimum)/input value
monitoring mode. (Hold down the key
for about one second.)
Changes the value or content
of a selected digit.
(Increments the value)
Holding down the Increment key for
about one second moves to the LO
judgment value indicator.
5.
Parameter Setup
5.1 Differences between Display Units
5.1.1 Multi-display Unit
Note: Pressing the Mode key displays the next parameter.
5.1.2 Single Display Unit
Note 1: Pressing the mode key with the parameter name shown changes the
display to the parameter information indication. If there is no key
operation for about one second when the parameter name is shown,
the display automatically changes to the parameter information
indication (however, this change does not automatically occur for
parameters PH/S-HI/FSC, etc., right after COND/COM/MET is in-
dicated).
Note 2: Pressing the Mode key when the parameter information indication
is shown results in the next parameter being displayed.
Note 3: If there is no key operation for about 8 seconds with the parameter
information indication shown, the display returns to the parameter
name indication.
Setup contents and parameter name
Setup contents
Parameter name
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
11
99.99mV
Offset : ± 9999
Full scale : 0 to ± 9999 100µV
1M
or more
± 100V
± (0.2% of FS
+10digit)
Input circuit : Single ended type
12
9.999V
1mV
± 250V
13
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 40 Hz to 1 kHz
Response speed : About 1 second
Dead zone : 0 to 99 digits
999.9mV
10µV
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
14
99.99V
Offset : ± 9999
Full scale : 0 to ± 9999 100mV
1M
or more
250V
± (0.2% of FS
+10digit)
Input circuit : Single ended type
15
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 40 Hz to 1 kHz
Response speed : About 1 second
Dead zone : 0 to 99 digits
600V
10mV
600V
± (0.3% of FS
+10digit)
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
11
99.99mV
Offset : ± 9999
Full scale : 0 to ± 9999 100µV
1M
or more
± 100V
± (0.2% of FS
+20digit)
12
9.999V
1mV
± 250V
13
999.9mV
10µV
Input circuit : Single ended type
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 40 Hz to 1 kHz
Response speed : About 1 second
Dead zone : 0 to 99 digits
Crest factor : 4:1 at full scale
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
14
99.99V
Offset : ± 9999
Full scale : 0 to ± 9999 100mV
1M
or more
250V
± (0.2% of FS
+20digit)
Input circuit : Single ended type
15
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 40 Hz to 1 kHz
Response speed : About 1 second
Dead zone : 0 to 99 digits
600V
10mV
600V
± (0.3% of FS
+20digit)
Crest factor : 4:1 at full scale
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
23
9.999mA
1µA
About
10
100mA
Offset : ± 9999
Full scale : 0 to ± 9999
± (0.5% of FS
+10digit)
500mA
3A
About
1
About
0.1
10µA
99.99mA
999.9mA
100µA
24
25
Input circuit : Single ended type
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 40 Hz to 1 kHz
Response speed : About 1 second
Dead zone : 0 to 99 digits
Crest factor : 4:1 at full scale
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
26
5A
1mA
(CT)
8A
Offset : ± 9999
Full scale : 0 to ± 9999
± (0.5% of FS
+10digit)
Input circuit : CT isoration type
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 50 Hz or 60Hz
Response speed : About 1 second
Dead zone : 0 to 99 digits
Crest factor : 4:1 at full scale
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
23
9.999mA
1µA
About
10
100mA
Offset : ± 9999
Full scale : 0 to ± 9999
± (0.5% of FS
+20digit)
500mA
3A
About
1
About
0.1
10µA
99.99mA
999.9mA
100µA
24
25
Input circuit : Single ended type
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 40 Hz to 1 kHz
Response speed : About 1 second
Dead zone : 0 to 99 digits
Crest factor : 4:1 at full scale
Range
Measurement
range
Indication
Highest
resolution
Input
impedance
Maximum
permissible
input
Accuracy
26
5A
1mA
(CT)
8A
Offset : ± 9999
Full scale : 0 to ± 9999
± (0.5% of FS
+20digit)
Input circuit : CT isoration type
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
Frequency range : 50 Hz or 60Hz
Response speed : About 1 second
Dead zone : 0 to 99 digits
Crest factor : 4:1 at full scale
Range
Measurement
range
Indication
Highest
resolution
Circuit
current
Accuracy
11
99.99
Offset : ± 9999
Full scale : 0 to ± 9999
10m
About
5mA
± (0.2% of FS)
Input circuit : Single ended type
12
999.9
13
14
9.999k
99.99k
Operating system :
conversion
Maximum sampling rate : 12.5 times per second
100m
1
10
About
500µA
About
50µA
About
5µA
Measuring system : Two-wire system or four-wire system
Open-circuit voltage : About 5 V
(internal socket change-over)
Range
Input
sensor
Indication
Highest
resolution
Accuracy
KA
0.1°C
(0.1°F)
± (0.5% of FS)
Input circuit : Single ended type
KB
J
T
Operating system :
conversion
Maximum sampling rate : 6.25 times per second
S
R
B
K
J
T
S
R
B
K
-50.0 to 199.9°C
(-58.0 to 391.8°F)
-50 to 1200°C
(-58 to 2192°F)
-50 to 1000°C
(-58 to 1832°F)
-50 to 400°C
(-58 to 752°F)
0 to 1700°C
(32 to 3092°F)
-10 to 1700°C
(14 to 3092°F)
100 to 1800°C
(212 to 3272°F)
1°C
(1°F)
± (0.2% of FS)
± (0.6% of FS)
± (0.4% of FS)
Note : The accuracy of range B is applicable
to temperatures of 500°C or more.
± (0.4% of FS)
Cold junction compensation error : ± 2°C(at 10 through 40°C)
Burnout alarm : It blinks by ---- display.
Internal resistance of sensor : 50 or less
Linearizer : Digital linearizer
Instruction Manual for FD5000 Series
4/12
Instruction Manual for FD5000 Series
9/12
8.1.4 AC Voltage Measuring Unit (average value detection: ranges
11 to 13)
8.1.5 AC Voltage Measuring Unit (average value detection: ranges
14 and 15)
8.1.6 AC Voltage Measuring Unit (true rms value: ranges 11 to 13)
8.1.7 AC Voltage Measuring Unit (true rms value: ranges 14 and
15)
8.1.8 AC Current Measuring Unit (average value detection: ranges
23 to 25)
8.1.9 AC Current Measuring Unit (average value detection: range
26)
8.1.10
AC Current Measuring Unit (true rms value: ranges 23 to 25)
8.1.11
AC Current Measuring Unit (true rms value: range 26)
8.1.12
Resistance Measuring Unit
8.1.13
Temperature Measuring Unit (TC)
(3)
(1)
(3)
(6) (7) (8) (9)
No.
Name
Main Functions
During measurement
During parameter setup
(1) Main display
Indicates the measured value.
IIndicates information on the
parameter to be set.
Indicates information on the item in the
maximum/minimum/(maximum-
minimum)/input value monitoring mode.
Judgment
indicators
HI
(2)
GO
LO
Indicates the result of judgment and
turns on if the measured value > HI
judgment value.
Indicates the result of judgment and
turns on if LO judgment value
$
the
measured value
$
HI judgment value.
Indicates the result of judgment and
turns on if the measured value < LO
judgment value.
(3) Function
indicators
ME
Turns on if "digital zero backup" is on.
PH
Turns on if "peak hold/valley hold/peak -
valley hold" is on.
Turns on if "digital zero" is on.
DZ
RE
Turns on if remote control is being
performed through RS-232C or RS-485
interface.
Flashes when linearization data output
values are set.
Flashes when linearization data input
values are set.
(6) Enter key
Pressing the Mode and Enter keys
together changes to the parameter
setting mode.
Pressing the Enter and Increment keys
together changes to the maximum/
minimum/(maximum-minimum)/input
value monitoring mode.
Switches from the maximum/minimum/
(maximum-maximum/minimum/
(maximum-minimum)/input value
monitoring mode to the comparative
judgment reading mode.
Returns to the measurement
mode.
Mode key
(7)
Pressing the Mode and Enter keys
together changes to the parameter
setting mode.
Selects the item to be set.
Pressing the Mode and Shift keys
together changes to the shift function
setup mode.
Pressing the Mode and Incremental
keys together turns on/off the "Digital
zero" indicator.
(1)
(2)
(6) (7) (8) (9)
Mode key
(7)
Pressing the Mode and Enter keys
together changes to the parameter
setting mode.
Selects the item to be set.
Pressing the Mode and Shift keys
together changes to the shift function
setup mode.
Pressing the Mode and Incremental
keys together turns on/off the "Digital
zero" indicator.
(8) Shift key
Pressing the Shift and Enter keys
together changes to the parameter
checking mode. (Comparator data
can be set.)
Pressing the Shift and Mode keys
together changes to the shift function
setup mode.
Selects from items in the maximum/
minimum/(maximum-minimum)/input
value monitoring mode. (Hold down
the key for about one second.)
Changes the digit to be set.
Increment key
(9)
Pressing the Increment and Mode
keys together turns on/off the "Digital
zero" indicator.
Pressing the Increment and Enter
keys changes to the maximum/
minimum/(maximum-minimum)/input
value monitoring mode.
Resets the maximum/minimum/
(maximum-minimum)/input value
monitoring mode. (Hold down the key
for about one second.)
Changes the value or content
of a selected digit.
(Increments the value)
