FT500 SFI / FT500LITE SFI
74
Boost+ button:
Increases boost pressure while is switched on.
None
Boost+ button input selection
White 1: Avaliable
White 2: Avaliable
White 3: Avaliable
White 4: Avaliable
General config 13/13
General config 12/13
Disab
Enab
Boost+ Scramble
Button increase:
12.0
psi
Activated at 12V
Activated at 0V
Button mode
2-step target:
Set the target pressure during 2-step.
3-step target:
Set the target pressure during 3-step.
Burnout target:
Set the target pressure during burnout mode.
2-step target
29.0
psi
3-step target
12.0
psi
Launch targets 1/2
Burnout target
12.0
psi
Launch targets 2/2
Launch targets
Defines the target pressure at the top of the valve in 2-step, 3-step
and burnout mode.
General config
Launch targets
Main targets
Wastegate boost pressure control
General config
Launch targets
Main targets
Wastegate boost pressure control
Boost maps
In this function you can set modes of boost maps by time after 2-step
(single-stage), by gear and engine RPM (a stage for each gear), by
gear elapsed time (a stage by each gear) and single value target.
Gear and
Engine RPM
Gear elapsed
time
Time based
after 2-step
Single target
valve
Engine RPM
based
Main targets 1/8
Main targets 3/8
0.00
2.50
5.00
10.00
7.50
2.50
2.00
1.50
1.00
0.50
0
Main targets 2/8
[psi]
+
-
5
3
2
Boost
[bar]
5.00
3.00
0.35
0.20
Time
[s]
4.00
Time based wategate pressure after 2-step
0.15
4
0.10
2.00
1
0.00
1.00
By time after 2-step:
Allows a detailed ramp up to 32 time points.
The intermediate values are interpolated.
Other functions
Wastegate pressure for gear 1 - 2/8
2400 RPM
1.05
psi
Gear and
Engine RPM
Gear elapsed
time
Time based
after 2-step
Single target
valve
Engine RPM
based
Main targets 1/8
By gear and engine RPM:
set up a stage for each gear, with up to 8
points per engine RPM. It is necessary that the gear change detection
function is enabled. It does not depend on 2-step.
Gear and
Engine RPM
Gear elapsed
time
Time based
after 2-step
Single target
valve
Engine RPM
based
Main targets 1/8
Main targets 2/8
[bar]
+
-
3
1
Boost
[bar]
70
50
1.20
0.50
Time
[s]
50
0.00
2
Wastegate pressure table for gear 1
Gear and
Engine RPM
Gear elapsed
time
Time based
after 2-step
Single target
valve
Engine RPM
based
Main targets 1/8
Main targets 2/8
Wastegate pressure fixed target
0.0
psi
Main targets 8/8
0,00
2,50
5,00
10,00
7,50
250
200
150
100
50
0
Gear 3
Gear 5
Chart curves
OK
Gear 1
Gear 2
Gear 4
Gear 6
Main targets 8/8
0,00
2,50
5,00
10,00
7,50
2.50
2.00
1.50
1.00
0,50
0
By gear elapsed time:
Set up a stage for each gear, with up to 8
time points after the shift.
Single target value:
Sets a fixed pressure for BoostController. The
wastegate valve will always work this pressure.
This mode is recommended for dynamometer tests.
Main targets 8/8
0
2500
5000
10000
7500
2.50
2.00
1.50
1.00
0,50
0
Main targets 2/8
[bar]
+
-
3
1
Pressure
[bar]
0.70
0.50
3000
2000
Revs
[RPM]
0.50
1000
2
RPM based wategate pressure
Gear and
Engine RPM
Gear elapsed
time
Time based
after 2-step
Single target
valve
Engine RPM
based
Main targets 1/8
By engine RPM:
Adjust the wastegate pressure according to the
engine RPM only.
