7
FE
48
ELLIPTICAL
1
FE
48
ASSEMBLY INSTRUCTIONS
CONSOLE MAST & CONSOLE
1.
Install the Incline Rail Assembly
(2)
into the U-channel bracket of the
Main Frame
(1)
. Secure with the six bolts & associated hardware as
follows: From the sides install two Hex Head Bolts
(114)
with two
Flat Washers
(144)
and two Nylon Nuts
(137).
From the top install
four Hex Head Bolts
(112)
, four Split Washers
(155)
, four Flat
Washers
(146)
, and four Star Washers
(156)
, as shown in figure1 and
tighten with the Wrenches provided
(160 & 163)
.
2.
Connect the 3 wire harness
(54)
to the female receiver cable coming
from the Incline rail assembly
(14)
. Connect the Three pin position
Sensor connector
(53)
to the female receiver coming from the
Incline rail assembly
(14).
3.
Locate the Console Mast
(10)
and Console Mast Cover
(91)
and slide
the Cover onto the Mast as far as it will go. Make sure the Console
Mast Cover is facing the correct way. At the top opening of the Main
Frame of the elliptical is a Computer Cable
(41)
. Secure the free end
of the twist tie that exits the bottom of the console mast
(10)
to this
cable. Pull the opposite end of this twist tie up through the console
mast
(10)
until the cable exits the top. Install the Console Mast
(10)
into the receiving bracket on the top of the Main Frame
(1)
. Pull
slightly on the computer cable at the top of the mast while installing.
This will ensure the cable does not get pinched and shorted during
console mast assembly.
4.
Put four Split Washers
(154)
onto the Long Hex Head Bolt
(113)
and
install through the left side of the receiving bracket into the Console
Mast
(10)
. Put the two Curved Washers
(153)
and the two Flat
Washers
(144)
onto the three Short Hex Head Bolts
(116)
and install
through the front of the console mast. Using the Wrench
(160)
,
tighten the three bolts, and the fourth bolt, which is pre-installed,
firmly. These bolts should be tightened as much as you possibly can.
5.
Plug all of the connectors into the back of the console; Computer
Cable
(41)
, two Hand pulse Cables
(47)
, Resistance switch wire
(56)
and Incline switch wire
(57)
. Secure the Console
(38)
on the console
mounting plate with four Phillips Head Screws
(123)
.
Hardware Step 1
#112.
5/16" × 2-1/4"_
Hex Head Bolt (4 pcs)
#113.
3/8" × 3/4"_
Hex Head Bolt (1 pc)
#114.
3/8" × 1-1/2"_
Hex Head Bolt (2 pcs)
#116.
3/8" × 3-3/4"_
Hex Head Bolt (3 pcs)
#123.
M5 × 10m/m_
Phillips Head Screw
(4 pcs)
#137.
3/8" × 7T_
Nyloc Nut (2 pcs)
#144.
Ø3/8" × Ø19 ×
1.5T_ Flat Washer (4 pcs)
#146.
Ø5/16" × Ø20 ×
1.5T_ Flat Washer (4 pcs)
#153.
Ø3/8" × 23 ×
2.0T_Curved Washer
(2 pcs)
#154.
Ø10 × 2T_
Spring Washer (4 pcs)
#155.
Ø8 × 1.5T_
Spring Washer (4 pcs)
#156.
Ø5/16"_
Star Washer (4 pcs)
