fruitcore robotics HORST600 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 92

background image

5 Assembly of the Robot

26

5.2

Assembly of the Robot

DANGER!
Danger due to incorrect assembly and commissioning



Assembly and commissioning must be performed only by persons with technical and elec-
trotechnical training who were also authorized by fruitcore robotics GmbH.

CAUTION!
Risk of injury due to the robot falling



Secure the robot against tilting until it is attached to the mounting surface.

ATTENTION!

Risk of damage to the robot.



Only lift the robot by the swivel arm.



Do not move the robot axes with force.

For the specifications regarding the condition of the mounting surface, see the following
subsection.

Note before setting up:

5.2.1

Mounting Surface

The robot must be mounted on a suitable, level, firm, dry, vibration-free, and non-moving surface with
mounting screws. The mounting surface should be made of steel or aluminum or possess comparable
strength values.
The load-bearing capacity of the mounting surface must be at least five times the weight of the robot and
nine times the maximum tilting moment of the robot with load capacity (320 Nm). The maximum load
capacity is taken into account in these values.
The robot is not designed for movement on a linear axis or a moving platform. Permissible acceleration
torques must be requested from the manufacturer, fruitcore GmbH. The robot must be assembled on a

level surface with a maximum tilt of 5°. Wall or ceiling

-mounting only on consultation with fruitcore robot-

ics GmbH.



Check the modules for damage. Do not mount/use damaged parts.



Ensure that there is sufficient room for the robot arm to move freely. There must be no obsta-
cles in the working area.



If the robot is combined with other machinery in a system, make sure that the other machinery
cannot damage the robot.



Ensure that suitable protection devices (e.g. separating protection device, light curtain, or

safety laser scanner) are installed. The protection devices must stop the robot’s movement

within the danger zone.



Protection devices (emergency stop, safety stop) must be connected only to safety-critical in-
terfaces and must be designed to be redundant.



«
...
32
33
34
35
36
...
»

Содержание HORST600





























































































Отзывы:

Нет отзывов

Похожие инструкции для HORST600

KR QUANTEC extra

Бренд: Kuka Страницы: 127

Бренд: Pro's Kit Страницы: 48

Бренд: LSLIDAR Страницы: 21

Бренд: Marvelmind Страницы: 263

I&J4000-LF Series

Бренд: I&J Fisnar Страницы: 130

Бренд: Xtrem Bots Страницы: 16

PATROL XT380972

Бренд: Xtrem Bots Страницы: 52

Бренд: ABB Страницы: 34

Бренд: Arrow Страницы: 2

MICRONOID CODE MAGNA

Бренд: Meccano Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды