Fronius TransSteel 3000c Pulse Скачать руководство пользователя страница 48

Страница: 48 / 140

Commissioning

Safety

WARNING!

An electric shock can be fatal.

If the power source is connected to the grid during installation, there is a danger of seri-
ous personal injury and property damage.

▶

Only carry out work on the device when the power source's power switch is in the -
O - position.

▶

Only carry out work on the device when the power source has been disconnected
from the grid.

WARNING!

Danger of electrical current due to electrically conductive dust in the device.

This can result in severe personal injury and damage to property.

▶

Only operate the device if an air filter is fitted. The air filter is a very important safety
device for achieving IP 23 protection.

General

Commissioning is described with reference to a manual, water-cooled MIG/MAG applica-
tion.

Information on
system compon-
ents

The steps and activities described below include references to various system compon-
ents, such as
-

Trolley

Upright bracket

Cooling units

Welding torches, etc.

For more detailed information about installing and connecting the system components,
please refer to the appropriate Operating Instructions for the system components.

Содержание TransSteel 3000c Pulse













































































































































Результаты поиска

Содержание TransSteel 3000c Pulse

Отзывы:

Похожие инструкции для TransSteel 3000c Pulse

Бренды по названию

Популярные бренды

Fronius TransSteel 3000c Pulse, Руководство по эксплуатации

Результаты поиска

Содержание TransSteel 3000c Pulse

Отзывы:

Похожие инструкции для TransSteel 3000c Pulse

Бренды по названию

Популярные бренды