manualshive.com logo in svg

Fronius IG Plus 100 V-1, Руководство по эксплуатации

Поделиться
Скачать
Fronius IG Plus 100 V-1 Скачать руководство пользователя страница 147

145

g

Replacing String Fuses

Safety

Preparation

WARNING!

An electric shock can be fatal. Danger due to grid voltage and DC 

voltage from solar modules.

-

The connection area should only be opened by a licensed electrician.

-

The separate power stage set area should only be disconnected from the 
connection area after first being disconnected from the grid power.

-

The separate power stage set area should only be opened by Fronius-trained 
service personnel.

Never work with live wires! Prior to all connection work, make sure that the AC 
and DC wires are not charged.

The DC main switch is only used to switch off power to the power stage set. When 
the DC main switch is turned off, the connection area is still energized.

WARNING!

An electric shock can be fatal. Danger from residual voltage from ca-

pacitors.

You must wait until the capacitors have discharged. Discharge takes 5 minutes.

off

on

1

2

OFF

AC

1

1

4

2

3

2

Содержание IG Plus 100 V-1









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды