13
O
pe
ra
te
Step 3: Setting the Control Dial
This system is designed to work effectively with a variety of pool equipment as long as the following procedures are followed.
Set the control dial by matching up the parameters of your pool on the chart below. THIS IS A STARTING POINT ONLY and may need
to be adjusted to fit your individual pool needs. See #2 below for adjusting directions.
IMPORTANT:
If using a multi-speed pump,
pump-run times of at least 6 hours per day at high speed are recommended for proper performance.
If running the pump at low speed only or on high speed less than 6 hours per day, please follow the 24 hour low-speed
directions below.
1.
For the first week, test the pool
water daily for free chlorine with
FROG Test Strips to ensure correct
dial setting. Continue to test weekly
throughout the season.
2.
After each testing, adjust the dial
up by 1/2 increment if the free
chlorine reading has dropped
below 0.5 ppm or adjust down by
1/2 increment if the reading has
risen above 1.0 ppm. Continue
this process each day until the free
chlorine reading stabilizes to at
least 0.5 ppm.
Remember to adjust dial by
1/2 increments only in order to
prevent over chlorination which
may bleach pool surfaces.
Find your starting dial setting by matching up the parameters of your
pool on the above chart. A pool with approximately 12,000 gallons
with a 1 horsepower pump running 12 hours a day would require a
starting setting of 4.5.
^ – Bypass installation recommended. See “Installation Tips” on page 6. RECOMMENDED FLOW RATE: 20-60 gpm
NR – This pump size is not recommended for this size pool.
24 HOUR, LOW-SPEED PUMP-RUN TIME
In order to ensure proper performance when running the
pump on low speed for 24 hours per day or high speed less
than 6 hours per day, bleed the air while the pump is on by
unscrewing the back knob until water appears. Then screw
the knob back in. Repeat this process each time the cap is
removed for any reason. Set the control dial at #6 and follow
the adjustment directions in Step 2 to determine the correct
setting for your pool.
POOL SIZE
Gallons Diameter
8 HOUR PUMP RUN TIME
12 HOUR PUMP RUN TIME
24 HOUR PUMP RUN TIME
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
7,000 (18’)
5.0
4.5
4.0
3.5
4.5
4.0
3.0
5.0^
3.5
3.0
2.5
4.0^
9,000 (21’)
5.5
5.0
4.5
4.0
5.0
4.5
4.0
5.5^
4.0
3.5
3.0
4.5^
12,000 (24’)
6.0
5.5
5.0
4.5
5.5
5.0
4.5
4.0
4.5
4.0
3.5
5.0^
15,000
NR
6.0
5.5
5.0
6.0
5.5
5.0
4.5
5.0
4.5
4.0
3.5
20,000
NR
NR
6.0
5.5
NR
6.0
5.5
5.0
5.5
5.0
4.5
4.0
25,000
NR
NR
6.5
6.0
NR
6.5
6.0
5.5
6.0
5.5
5.0
4.5
POOL SIZE
Gallons Diameter
12 HOUR PUMP RUN TIME
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
7,000 (18’)
4.5
4.0
3.0
5.0^
9,000 (21’)
5.0
4.5
4.0
5.5^
12,000 (24’)
5.5
5.0
4.5
4.0
15,000
6.0
5.5
5.0
4.5
20,000
NR
6.0
5.5
5.0
25,000
NR
6.5
6.0
5.5
IMPORTANT:
Control dial settings in excess of these
recommendations could result in excess trichlor levels being
discharged into the pool. This can result in bleaching or
discoloration of areas around the pool inlet or, in some cases,
bleaching or discoloration of the entire pool liner or paint. In
addition, excess trichlor in the pool can create health hazards
to bathers.
EXAMPLE