Fritsch ANALYSETTE 3 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 58

background image

WARNING!
The maximum accepted concentration (MAC) levels of

the relevant safety guidelines must be observed; if nec-

essary, ventilation must be provided or the machine

must be operated under an extractor hood.

DANGER!
Explosion hazard!
– When Sieving oxidizable substances, e.g. metals or

coal, there is a risk of spontaneous combustion

(dust explosion) if the share of fine particles

exceeds a certain percentage. When Sieving these

kinds of substances, special safety measures must

be taken and the work must be supervised from a

specialist.

– The high-speed rotor mill is not explosion pro-

tected and is not designed to sieve explosive mate-

rials.

n

Do not remove the information signs.

NOTICE!
Immediately replace damaged or illegible information

signs.

n

Unauthorised alteration of the the ANALYSETTE 3 will void Fritsch's

declaration of conformity to European directives and void the guar-

antee.

n

Only use the the ANALYSETTE 3 when it is in proper working order, as

intended and in a safety- and hazard-conscious manner adhering to

the operating manual. In particular, immediately rectify any malfunc-

tions that could pose a safety hazard.

n

If, after reading the operating manual, there are still questions or

problems, please do not hesitate to contact our specialised per-

sonnel.

2.6 Protective equipment

Protective equipment is to be used as intended and may

not be disabled or removed.
All protective equipment is to be regularly checked for

integrity and proper functioning.

Safety information and use

- 15 -

«
...
15
16
17
18
19
...
»

Содержание ANALYSETTE 3



























































Отзывы:

Нет отзывов

Похожие инструкции для ANALYSETTE 3

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: XM Fitness Страницы: 10

Бренд: HABYS Страницы: 16

Бренд: IDEAL Страницы: 12

Бренд: olympia electronics Страницы: 4

Бренд: ubbink Страницы: 30

Бренд: York Страницы: 16

i.Profiler plus

Бренд: Zeiss Страницы: 66

Бренд: ZOLL Страницы: 48

Бренд: ubicquia Страницы: 36

Бренд: xsto Страницы: 63

ENIDINE ENI-VIBE 33VC4400B

Бренд: Dytran Страницы: 2

Бренд: Mecc Alte spa Страницы: 12

Signature IVAC 710 Series

Бренд: Alaris Medical Systems Страницы: 140

AX2090-ND80 Series

Бренд: Beckhoff Страницы: 41

Бренд: Delta Light Страницы: 2

Бренд: Nordson EFD Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды