Fritsch ANALYSETTE 3 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 58

background image

Do not switch off the device during this work. When the

device is switched off, the sample material can stick or

glue to the sieves.

Transfer (rinse) the sieve residue into weighed bottles and dry it.
Now the lower sieves can be sieved further. Continue dismantling as

described above.

NOTICE!
The sieve stack must remain filled with liquid during the

entire sieving process.
The sieve foils must not run dry!
That can cause irreparable damage to the sieves.

Torn sieve foils can be soldered with soft solder, point by

point from underneath.

6.5 Standby

If the device is not operated for approx. one hour, it switches to energy-

saving mode (STANDBY). Only the STANDBY lamp lights up.
The device is switched to normal mode by pressing the START key. The

POWER lamp lights up, the STANDBY lamp goes out.

6.6 Setting the sieving time

The sieving time can be set in increments of minutes using the +/- keys.

Values between 1 and 99 minutes are possible; after a sieving time of 1

hour, let the device cool down.
Continuous operation is set by holding down the "-" key until "P" or "00"

appears on the display.

Using the device

- 31 -

«
...
31
32
33
34
35
...
»

Содержание ANALYSETTE 3



























































Отзывы:

Нет отзывов

Похожие инструкции для ANALYSETTE 3

Бренд: Rabe Страницы: 65

Бренд: Rangevision Страницы: 31

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Garmin Страницы: 20

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды