Fritsch ANALYSETTE 3 Скачать руководство пользователя страница 41

Страница: 41 / 58

7.5.1 Conducting a grinding operation

7.5.1.1

Fitting and clamping the mortar

Move the clamping lever on the belt clamping device downwards

and insert the toothed belt through the holder from the inside to

the outside. (See

Chapter 6.1.1 „Fitting and clamping the

sieves“ on page 23).

Place the mortar and the ball on the vibratory plate. The mortar

must be positioned in the round gap of the vibratory plate without

being wedged.

Unscrew the knurled knob on the toothed belt as far as possible.

Pour in the grinding stock.

Put on the clamping lid.

Attach the knurled knob to the lid

Lightly pull the toothed belt tight and move it upwards until its

teeth interlock with the teeth of the belt clamping device.

Move the clamping lever upwards.

Make sure that the teeth of the toothed belt

interlock with the teeth of the belt clamping

device!

By turning the knurled knobs to the right, tighten the mortar

evenly until the toothed belts are tightly clamped!

If the two toothed belts are not evenly clamped,

it is possible that the grinding stock will escape

from the mortar.

Select an amplitude for grinding at which the ball vibrates. The best

grinding results can be achieved at a medium amplitude (1 mm to max. 2

mm), as the impact frequency of the grinding ball is then highest.
Similar to the ANALYSETTE 3 SPARTAN, the amplitude is set manually

with the Plus and Minus key on the control panel and viewed on the lid.

(See

Chapter 6.7.1 „Displaying the amplitude“ on page 32).

NOTICE!
Do not allow the grinding balls to jump too high. This

can cause damage to the lid!
Start grinding at low a amplitude and increase it slowly

- do not select an amplitude that is too high! (

≤

2 mm)

Accessories

- 39 -

Содержание ANALYSETTE 3



























































Результаты поиска

Содержание ANALYSETTE 3

Отзывы:

Бренды по названию

Популярные бренды

Fritsch ANALYSETTE 3, Руководство по эксплуатации

Результаты поиска

Содержание ANALYSETTE 3

Отзывы:

Бренды по названию

Популярные бренды