manualshive.com logo in svg

Fritsch ANALYSETTE 3, Руководство по эксплуатации

Поделиться
Скачать
Fritsch ANALYSETTE 3 Скачать руководство пользователя страница 15

DANGER!
This symbol and keyword combination designates con-

tents and instructions for proper use of the machine in

explosive areas or with explosive substances. Ignoring

information with this designation will result in serious

or fatal injury.

DANGER!
This symbol and keyword combination designates con-

tents and instructions for proper use of the machine

with combustible substances. Ignoring information with

this designation will result in serious or fatal injury.

WARNING!
This symbol and keyword combination points out a

directly hazardous situation due to movable parts.

Ignoring information with this designation can result in

hand injuries.

WARNING!
This symbol and keyword combination points out a

directly hazardous situation due to hot surfaces.

Ignoring information with this designation can result in

serious burn injuries due to skin contact with hot sur-

faces.

Safety information can refer to specific, individual procedure instruc-

tions. Such safety information is embedded in the procedure instructions

so that the text can be read without interruption as the procedure is

being carried out. The keywords described above are used.
Example:
1.

Loosen screw.

2.

CAUTION!
Risk of entrapment at the lid.

Close the lid carefully.

3.

Tighten screw.

Safety information in the procedure

instructions

 

Safety information and use

 

 

- 13 -

 

Содержание ANALYSETTE 3



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды