Frigidaire Fully Integrated Direct FeedModel Dishwashers страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 36

background image

19

At time codes may appear in the display below are a list of codes. Not all codes are failure or error codes so
be sure to read what the code means.

Control Codes

Display

Reason for Code

When is a wash cycle the control does not receive the proper indication that
the vent is closed. The control will try to reseat the vent if after 5 attempts
the vent does not close the failure will appear. The cycle will not start.

When in the dry mode, the control does not receive the proper feedback from
the vent that the fan is running at the proper speed. The failure will appear
and the control shuts down

When the control verifies that any of the pads on the membrane switch has
been closed for one minute the failure will appear in the display

On power up the control verifies a problem with the options the failure will
appear.

The control is not receiving power from the door switch

This will be seen in the r/t test if pad # 4 has been pressed

This will be seen in the r/t test if pad # 1 has been pressed

HO

Heat delay

The control has extend the length of a cycle to allow for in increase in water
temperature

The control has sensed a problem with the Hall style sensor in the wash motor.

LO

Low rinse aid

The control has received a signal form the rinse aid dispenser that the rinse agent
level is low.

The control has experienced drop in power to the processor

The control has sensed a problem with the reed switch in the Rinse aid dispenser

RE

Rinse aid

The reed switch in the rinse aid dispenser is closed. This can be seen in the r/t
test if pad # 7 has been pressed

RF

Rinse aid

The reed switch in the rinse aid dispenser is open. This can be seen in the r/t test
if pad # 7 has been pressed

The control has entered the r/t test program

The detergent dispenser has been activated

tu

Tubidity sensor

The control has sensed a failure in the turbidity sensor while in the
Water Service test.

The control has been programmed for a UL test mode.

UL

UL test mode

rt

Relay/triac test

Sd

Detergent disp.

rA

Rinse aid

PF

Power failure

FL

Water valve is on

hs

Hall Sensor

CL

Door switch open

dP

Drain pump operations

"Er"

Membrane Switch failure

"CE"

Configuration error

What it indicates

"uo"

Vent open

"uF"

Fan is not running

«
...
17
18
19
20
21
...
»

Содержание Fully Integrated Direct FeedModel Dishwashers





































Отзывы:

Нет отзывов

Похожие инструкции для Fully Integrated Direct FeedModel Dishwashers

Бренд: Magic Chef Страницы: 30

Бренд: Magic Chef Страницы: 8

Бренд: Indesit Страницы: 72

Бренд: NEFF Страницы: 60

SteamScrubber 4010010 Series

Бренд: Labconco Страницы: 108

Бренд: BALAY Страницы: 28

Бренд: Leonard Страницы: 497

AdorinaWash V400

Бренд: V-ZUG Страницы: 20

Бренд: Haier Страницы: 44

Бренд: Haier Страницы: 56

Бренд: Haier Страницы: 44

Бренд: Haier Страницы: 100

Бренд: Haier Страницы: 64

Бренд: Haier Страницы: 65

Бренд: Haier Страницы: 64

Бренд: Haier Страницы: 33

Бренд: Beko Страницы: 36

Бренд: Beko Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды