FRIEDLAND SA5 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

FRIEDLAND SA5 Скачать руководство пользователя страница 11

11

5. The Control Panel must be located within reach
of a mains socket.

6.

If any of the telephone based functions are to be

used then the Control Panel will need connecting to a
convenient telephone point.

Note:

It is recommended that the telephone connection

lead is not extended beyond 10 metres before
connecting to a telephone master or secondary outlet.

7. Note:

DO NOT fix the Control Panel onto or very

close to metalwork (i.e. radiators, water pipes, etc) as
this could affect the radio range of the device.

INSTALLING THE CONTROL PANEL

1.

Undo the 2 cover fixing screws on top of the panel

and open the cover. The cover is hinged along the
bottom edge.

2.

Unclip and remove the two back-up batteries on

either side of the panel.

3.

Hold the Control Panel in position on the wall and

mark the positions of the four fixing holes. Remove the
panel, drill four 5mm holes and fit the 22mm wall plugs.

Note:

The wall plugs supplied with the product are not

suitable for plasterboard walls. If mounting the Control
Panel onto plasterboard use appropriate wall plugs.

IMPORTANT:

Do not drill the fixing holes with the

Control Panel in position; as the resulting dust and

vibration may damage the Control Panel’s internal

components and invalidate the guarantee.

4.

Fit two 18mm No.4 screws into the top holes until

3mm protrudes from the wall face and hang the Control
Panel over these screws using the two keyhole slots in
the top corners of the panel casing.

5.

Route the cable from the Power Supply Unit up

behind and on the right hand side of the Control Panel
and connect the plug to the DC power socket in the
panel. Ensuring that the cable is not trapped between
the panel and the wall.

6.

Fix the Panel to the wall using two 18mm No.4

screws in the lower fixing holes in the panel and tighten
the upper fixing screws until they just grip the casing.
Do not over tighten the fixing screws as this could
damage or distort the casing.

��

��

��

��

��

��

�

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��
��

��
��

��
��

��
��

��
��

��
��

Inside View of Control Panel

«
...
9
10
11
12
13
...
»

Содержание SA5





















































Отзывы:

Нет отзывов