Frick XJF 120 Скачать руководство пользователя страница 4

Страница: 4 / 28

S70-101SM
Page 4

Frick XJS and XJF Rotary Screw Compressor

Service Manual

TORQUE DATA

Torque requirements applicable to the procedures contained in this
manual are listed below.

TORQUE SPECIFICATIONS

CAPSCREW SIZE

TORQUE VALUE

ENGLISH

METRIC

SOCKET SIZE

M4
M5
M6
M8

M12
M16
M20

M22*

2 ft-lb
4 ft-lb
7 ft-lb

18 ft-lb
58 ft-lb

144 ft-lb
260 ft-lb
368 ft-lb

2.7Nm

5.4 Nm

9.5 Nm

24.4 Nm
78.7 Nm

195.3 Nm
352.5 Nm

499 Nm

3 mm
4 mm
5 mm
6 mm

10 mm
14 mm
17 mm
32 mm

* Hex Head
NOTE: To convert foot-pounds of torque to metric Newton-meters, mul-
tiply foot-pounds times 1.3558 (Example: 75 ft-lbs x 1.3558 equals 101.7
Nm)

SAFETY PRECAUTIONS

DANGERS, WARNINGS, CAUTIONS, and NOTES are
strategically placed throughout this manual to further em-
phasize the importance of personal safety, qualifications of
user personnel, and proper use or maintenance of the equip-
ment. These precautions supplement and/or complement
standard industry practices and the safety information decals
affixed to applicable areas of the equipment. Safety Precau-
tions are defined as follows:

GENERAL SAFETY PRACTICES

It would be impossible to compile a list of all Safety
Practices applicable to the operation and maintenance of the
equipment covered in this manual. This is brought about in
part by the diverse operating environments, as well as the
varied applications and customer-specified configurations.
The following Safety Practices are provided as a guide in
promoting safety during routine operation, service, inspec-
tion, and maintenance of Frick compressors. This informa-
tion, combined with standard industry safety practices, lo-
cal, state, and federal regulations, establish the overall safety
requirements for the workplace.

Always shut down unit and discon-
nect power before making any ad-
justments or repairs.

Operating a damaged unit is not
only unsafe, but continued use will
cause additional damage and/or
component failure.

DO NOT attempt any operation or
perform any maintenance before
you read and understand all Safety
Practices in this manual.

Ensure that work area is ad-
equately ventilated, and wear
proper safety equipment when
compressor is open to atmosphere.

Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.

Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.

Indicates a potentially hazardous
situation or practice which, if not
avoided,will result in damage to
equipment and/or minor injury.

Indicates an operating procedure,
practice, etc., or portion thereof
which is essential to highlight.

NOTE:

SPECIAL TOOLS AND TEST EQUIPMENT

Special tools and/or test equipment required to perform the
maintenance procedures contained in this manual are listed
below.

Frick Manufactured

Local Sourced

Owattona Tool Co.
Owattona Tool Co.

Local Purchase

Equipment

Manufacturer

Part No.

943

1123

Compressor Size

95mm

120mm

Equipment

Item No.

Complete Tool Kit
Wrench, Crowfoot
Wrench, Spanner
Gear Cover Guide Rod
8mm T-wrench
8mm Pinion Gear Puller
8mm Seal Installation and

Removal Tool

8mm Disc Bearing Puller
8mm Disc Bearing

Removal Tool

8mm Clamping Collar
8mm Discharge Bearing

Installation Tool

Tool Shaft Seal
Screw, 8mm

534C0008G01

111Q0452437
111Q0452438

534B0192H01
534C0456G01
534C0521G01
534C0523H01

534C0528G01
534C0534G01

534C0673G01
534D0434G01

534A0310H01

111Q0740796

534C0008G02

111Q0452437
111Q0452440
111Q0041972

534C0456G01
534C0520G01
534C0387H01

534C0529G01
534C0533G01

534C0673G02
534D0435G01

534A0310H02

111Q0740796

Bearing Puller
Roller Bearing Inner

Race Puller

12mm GuidePins

" lg. and 5

" lg.)

4" Hose Clamp

REPLACE WITH PAGE 2 ON THE PC!

DANGER

WARNING

CAUTION

WARNING

Property of American Airlines

Содержание XJF 120





























Результаты поиска

Содержание XJF 120

Отзывы:

Похожие инструкции для XJF 120

Бренды по названию

Популярные бренды

Frick XJF 120, Руководство по обслуживанию

Результаты поиска

Содержание XJF 120

Отзывы:

Похожие инструкции для XJF 120

Бренды по названию

Популярные бренды