Fri-Jado MCC 120 Скачать руководство пользователя страница 69

Страница: 69 / 105

Service Manual MCC Cold US 20220700

Page 69

9.3

Trouble Shooting Analytical description

Description of part

Symptoms

Possible causes

Solution / Action

Contactor

Contactor does not

work

Wiring

Coil malfunction

Contact burned

Check wiring

Check resistance of coil

+/- 525Ω

Check the contacts

Replace contactor

Cooling engine

(COLD unit)

Cooling system does

not initiate (compressor

doesn’t run

Wiring cooling

Engine

Compressor

Malfunction

Check wiring

Replace cooling engine

Tumble switch

Light, heating or cooling

does not switch on

Wiring

Contact burned

Check wiring

Check the voltage on “in“ and

“output“

LED

Light does not turn on

Wiring

LED broken

Led driver defect

Check Wiring

Replace LED

Replace LED driver

Electronic thermostat

Display does not light

The unit is not reaching

the set temperature

Wiring

Loose sensor

Thermostat

Malfunction

Thermostat setting

Check wiring

Check sensor

Replace thermostat

Check parameters

Defrost sensor

(Cold Unit)

Ice on evaporator

The unit is not reaching

the set temperature or

does not cool at all

The unit becomes too

cold

Condensor blocked

Broken Sensor

Loose sensor

Broken Sensor

Loose sensor

Clean condensor with long

haired soft brush

Replace sensor

Check sensor wiring

Replace sensor

Check sensor wiring

Air out sensor

(Cold Unit)

Ice on evaporator

The unit is not reaching

the set temperature or

does not cool at all

The unit becomes too

cold

Condensor blocked

Broken Sensor

Loose sensor

Broken Sensor

Loose sensor

Clean condensor with long

haired soft brush

Replace sensor

Check sensor wiring

Replace sensor

Check sensor wiring

Содержание MCC 120










































































































Результаты поиска

Содержание MCC 120

Отзывы:

Бренды по названию

Популярные бренды

Fri-Jado MCC 120, Руководство по обслуживанию

Результаты поиска

Содержание MCC 120

Отзывы:

Бренды по названию

Популярные бренды