Freescale Semiconductor PowerPC e500 Core Скачать руководство пользователя страница 300 | Manualshive

Страница: 300 / 548

background image

PowerPC e500 Core Family Reference Manual, Rev. 1

7-2

Freescale Semiconductor

Performance Monitor

•

PMRs:

— The performance monitor counter registers (PMC0–PMC3) are 32-bit counters used to

count software-selectable events. Each counter counts up to 128 events.
UPMC0–UPMC3 provide user-level read access to these registers. Reference events are
those that should be applicable to most microprocessor microarchitectures and be of
general value. They are identified in

Table 7-10

.

— The performance monitor global control register (PMGC0) controls the counting of

performance monitor events. It takes priority over all other performance monitor control
registers. UPMGC0 provides user-level read access to PMGC0.

— The performance monitor local control registers (PMLCa0–PMLCa3,

PMLCb0–PMLCb3) control each individual performance monitor counter. Each
counter has a corresponding PMLCa and PMLCb register. UPMLCa0–UPMLCa3 and
UPMLCb0–UPMLCb3 provide user-level read access to PMLCa0–PMLCa3,
PMLCb0–PMLCb3).

•

The performance monitor interrupt follows the Book E interrupt model and is assigned to
interrupt vector offset register 35 (IVOR35). Its priority is less than the fixed-interval
interrupt and greater than the decrementer interrupt.

Software communication with the performance monitor APU is achieved through PMRs rather
than SPRs. The PMRs are used for enabling conditions that can trigger a APU-defined
performance monitor interrupt.

7.2

Performance Monitor APU Registers

The performance monitor APU provides a set of PMRs for defining, enabling, and counting
conditions that trigger the performance interrupt. It also defines IVOR35 (SPR 531) for indicating
the address of the performance monitor interrupt vector. IVOR35 is described in

Section 2.7.1.5,

“Interrupt Vector Offset Registers (IVORs)

.”

The supervisor-level performance monitor registers in

Table 7-1

are accessed with mtpmr and

mfpmr. Attempting to read or write supervisor-level registers in user-mode causes a privilege
exception.

Table 7-1. Performance Monitor Registers–Supervisor Level

Number PMR[0–4] PMR[5–9]

Name

Abbreviation

16

00000

10000

Performance monitor counter 0

PMC0

17

00000

10001

Performance monitor counter 1

PMC1

18

00000

10010

Performance monitor counter 2

PMC2

19

00000

10011

Performance monitor counter 3

PMC3

144

00100

10000

Performance monitor local control a0

PMLCa0

«
...
298
299
300
301
302
...
»

Содержание PowerPC e500 Core





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerPC e500 Core

Бренд: EPOX Страницы: 54

Бренд: IBM Страницы: 40

TPS61090EVM-029

Бренд: Texas Instruments Страницы: 19

Бренд: Texas Instruments Страницы: 18

Бренд: Quick Страницы: 48

LCMXO3L-DSI-EVN

Бренд: Lattice Страницы: 2

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 84

Gamefisher 298.586180

Бренд: Gamefisher Страницы: 23

Бренд: IBASE Technology Страницы: 78

Lanparty JR P45-T2RS

Бренд: DFI Страницы: 146

Бренд: AOpen Страницы: 8

Бренд: Soyo Computer Страницы: 20

G31M-GS R2.0-QVL

Бренд: ASROCK Страницы: 2

Бренд: Sony Страницы: 7

Бренд: Sony Страницы: 138

Бренд: Glomation Страницы: 18

Бренд: Super Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды