Freescale Semiconductor MPC5200 Скачать руководство пользователя страница 4

MPC5200 ATA Interface, Rev. 0

ATA Interface

Freescale Semiconductor

4

2.3

IO Cable

The cable specification impacts system integrity and the maximum length that shall be supported in any 
application. Cable total length shall not exceed 0.46 m (18 in.). Cable capacitance shall not exceed 35 pF. 
80-pin grounded cable helps to avoid problems with noise and inductance although 40-pin cable is 
sufficient for modes up to UDMA-2 as in the ATA/ATAPI-4 spec. Also ATA/ATAPI-4 compliant 
termination is a must; otherwise, CRC checksum error may randomly occur.

Data bus bit 14

DD13

ATA_DATA_14

<>

16

Data bus bit 15

DD14

ATA_DATA_15

<>

18

Device active or slave (Device 1) 
present

DASP-

>

39

Device address bit 0

DA0

ATA_SA_0

>

35

Device address bit 1

DA1

ATA_SA_1

>

33

Device address bit 2

DA2

ATA_SA_2

>

36

DMA acknowledge

DMACK-

ATA_DACK_B

>

29

DMA request

DMARQ

ATA_DRQ

<

21

Interrupt request

INTRQ

ATA_INTRQ

<

31

I/O read
DMA ready during Ultra DMA data in 
bursts
Data strobe during Ultra DMA data 
out bursts

DIOR-

HDMARDY-

HSTROBE

ATA_IOR_B

>
>
>

25

I/O ready
DMA ready during Ultra DMA data 
out bursts
Data strobe during Ultra DMA data in 
bursts

IORDY-

DDMARDY-

DSTROBE

ATA_IOCHRDY

<
<
<

27

I/O write
Stop during Ultra DMA data bursts

DIOW-

STOP

ATA_IOW_B

>
>

23

Passed diagnostics
Cable assembly type identifier

PDIAG-

CBLID-

-

<>

34

Reset

RESET-

HRESET_B

>

1

Ground

GND

2,19,22,24,

26,

30,40

Table 2. ATA Signals (continued)

ATA Signal

ATA Acronym

 MPC5200 Pin

Direction

 40-Pin 

ATA Cable

Содержание MPC5200





















Отзывы: