background image

1 Introduction

This document describes the LS1043A reference design board
(LS1043ARDB) and hardware kit containing the board. It also
explains the basic board operations in a step-by-step manner.

This document describes the settings required to connect
switches, connectors, jumpers, push buttons, and LEDs to the
peripheral devices.

The LS1043ARDB functions with an integrated development
environment (IDE), such as Freescale CodeWarrior. The
instructions for working with the IDE are beyond the scope of
this document.

The list of items included in the LS1043ARDB hardware kit is
provided with the LS1043ARDB board support package
(BSP). Optional hardware components that are not included in
the LS1043ARDB hardware kit are:

• TDM modules
• PCIe/mini-PCIe cards
• CodeWarrior TAP (CWTAP)

2 Related documentation

The table below lists and explains the additional documents
that you can refer to, for more information about
LS1043ARDB.

Freescale Semiconductor

Document Number: LS1043ARDBQS

Quick Start

Rev. 1, 11/2015

QorIQ LS1043A Reference Design

Board Quick Start

© 2015 Freescale Semiconductor, Inc.

Contents

1

Introduction.............................. .............................. 1

2

Related documentation..................... .......................1

3

LS1043ARDB system board interface ....................2

4

Getting started with LS1043ARDB.... ....................3

5

Switch configurations................... ..........................4

6

Jumper settings......................... .............................. 8

7

Interfaces.................................................................9

8

Connectors.............................................................16

9

Push and slide buttons........................................... 18

10

LED indicators........................... ...........................19

11

Setting up CodeWarrior TAP............. .................. 21

12

LS1043ARDB operating
configurations................................... .................... 22

13

NOR flash memory map........................................24

14

Revision history.................................................... 24

Содержание LS1043ARDB



























Отзывы: