manualshive.com logo in svg

Freescale Semiconductor ColdFire MCF5211, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor ColdFire MCF5211 Скачать руководство пользователя страница 153

Reset Controller Module

MCF5213 ColdFire® Integrated Microcontroller Reference Manual, Rev. 3

Freescale Semiconductor

9-5

 

9.6

Functional Description

9.6.1

Reset Sources

Table 9-5

 defines the sources of reset and the signals driven by the reset controller.

To protect data integrity, a synchronous reset source is not acted upon by the reset control logic until the 
end of the current bus cycle. Reset is then asserted on the next rising edge of the system clock after the 
cycle is terminated. When the reset control logic must synchronize reset to the end of the bus cycle, the 
internal bus monitor is automatically enabled regardless of the BME bit state in the chip configuration 
register (CCR). Then, if the current bus cycle is not terminated normally, the bus monitor terminates the 
cycle based on the length of time programmed in the BMT field of the CCR.

Internal byte, word, or longword writes are guaranteed to complete without data corruption when a 
synchronous reset occurs. External writes, including longword writes to 16-bit ports, are also guaranteed 
to complete.

Asynchronous reset sources usually indicate a catastrophic failure. Therefore, the reset control logic does 
not wait for the current bus cycle to complete. Reset is asserted immediately to the system.

3

POR

Power-on reset flag. Indicates that the last reset was caused by a power-on reset.
1 Last reset caused by power-on reset
0 Last reset not caused by power-on reset

2

EXT

External reset flag. Indicates that the last reset was caused by an external device asserting the external RSTI pin.
1 Last reset state caused by external reset
0 Last reset not caused by external reset

1

LOC

Loss-of-clock reset flag. Indicates that the last reset state was caused by a PLL loss of clock.
1 Last reset caused by loss of clock
0 Last reset not caused by loss of clock

0

LOL

Loss-of-lock reset flag. Indicates that the last reset state was caused by a PLL loss of lock.
1 Last reset caused by a loss of lock
0 Last reset not caused by loss of lock

Table 9-5. Reset Source Summary

Source

Type

Power on

Asynchronous

External RSTI pin (not stop mode)

Synchronous

External RSTI pin (during stop mode)

Asynchronous

Loss-of-clock

Asynchronous

Loss-of-lock

Asynchronous

Software

Synchronous

LVD reset

Asynchronous

Table 9-4. RSR Field Descriptions (continued)

Field

Description

Содержание ColdFire MCF5211

































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды