Freescale Semiconductor C29x Скачать руководство пользователя

Страница: 51 / 65

7.2.13 Boot Configuration Register 1 (CPLD_BOOTCFG1)

NOTE

For more information on BOOTCFG1 register, refer to C29x
datasheet.

Address: 0h base + 18h offset = 18h

Bit

Read

cfg_core_

speed

cfg_core_pll[0:2]

cfg_sys_

speed

cfg_sys_pll[0:2]

Write

Reset

CPLD_BOOTCFG1 field descriptions

Field

Description

cfg_core_speed

Configuration core speed.

1–3

cfg_core_pll[0:2]

Configuration core PLL.

cfg_sys_speed

Configuration system speed.

5–7

cfg_sys_pll[0:2]

Configuration system PLL.

7.2.14 Boot Configuration Register 2 (CPLD_BOOTCFG2)

NOTE

For more information on BOOTCFG2 register, refer to C29x
datasheet.

Address: 0h base + 19h offset = 19h

Bit

Read

cfg_boot_seq[0:1]

cfg_plat_

speed

cfg_ddr_speed[0:1]

cfg_ddr_pll[0:2]

Write

Reset

Chapter 7 CPLD Specification

C29x PCIe Card User Guide, Rev. 0, 10/2013

Freescale Semiconductor, Inc.

Содержание C29x


































































Результаты поиска

Содержание C29x

Отзывы:

Похожие инструкции для C29x

Бренды по названию

Популярные бренды

Freescale Semiconductor C29x, Руководство пользователя

Результаты поиска

Содержание C29x

Отзывы:

Похожие инструкции для C29x

Бренды по названию

Популярные бренды