Freescale Semiconductor C29x Скачать руководство пользователя

Страница: 37 / 65

Table 6-1. POR configuration through switches

(continued)

Switch

POR

configuration

Signal name

Default

setting

Signal meaning

Settings

OFF (1): DDR data rate is greater than
or equal to 967 MHz.

cfg_ddr_speed[1]:

ON (0): When cfg_ddr_speed[0]=1 and
cfg_ddr_pll=10

OFF (1): When cfg_ddr_speed[0]=0
and (cfg_ddr_pll=8 or cfg_ddr_pll=10 or
cfg_ddr_pll>=12) or when
cfg_ddr_speed[0]=1 and
cfg_ddr_pll>=12

NA: When cfg_ddr_speed[0]=1 and
cfg_ddr_pll=8

SW6[6] cfg_plat_speed

IFC_PAR1

OFF

Platform speed
configuration input

ON (0): Platform clock frequency is
greater than or equal to 267 MHz and
less than 320 MHz.

OFF (1): Platform clock frequency is
greater than or equal to 320 MHz and
less than 401 MHz.

SW6[7] cfg_boot_seq[0]

IFC_A26

OFF

Boot sequencer
configuration options

SW6[7,8] ON OFF (01): Normal I

addressing mode is used. Boot
sequencer is enabled and loads
configuration information from a ROM
on the I

C1 interface. A valid ROM

must be present.

SW6[7,8] OFF ON (10): Extended I

addressing mode is used. Boot
sequencer is enabled and loads
configuration information from a ROM
on the I

C1 interface. A valid ROM

must be present.

SW6[7,8] OFF OFF (11): Boot
sequencer is disabled. No I

C ROM is

accessed. This is the default setting.

SW6[8] cfg_boot_seq[1]

IFC_A19

OFF

SW7[1] cfg_cpu_boot

DMA_DDONE0_
N

OFF

CPU boot
configuration inputs

ON (0): CPU boot hold off mode. The
e500 core is prevented from booting
until configured by an external master.

OFF (1): The e500 core is allowed to
boot without waiting for configuration by
an external master.

SW7[2] cfg_io_port[0]

IFC_AD13

Different I/O ports
active on the SerDes

SW7[2:4] ON ON ON (000): PCIe-x4 (5
GHz)

SW7[2:4] ON ON OFF (001): PCIe-x4
(2.5 GHz)

SW7[2:4] ON OFF ON (010): PCIe-x2
(5 GHz)

SW7[3] cfg_io_port[1]

IFC_AD14

SW7[4] cfg_io_port[2]

IFC_BCTL

OFF

Table continues on the next page...

Chapter 6 POR Configuration

C29x PCIe Card User Guide, Rev. 0, 10/2013

Freescale Semiconductor, Inc.

Содержание C29x


































































Результаты поиска

Содержание C29x

Отзывы:

Похожие инструкции для C29x

Бренды по названию

Популярные бренды

Freescale Semiconductor C29x, Руководство пользователя

Результаты поиска

Содержание C29x

Отзывы:

Похожие инструкции для C29x

Бренды по названию

Популярные бренды