REAR PANEL
HOW TO USE FT-1Y
1!
IN Terminal
Input terminal for the FT-1Y. Connect your guitar or effects
unit to this terminal.
1@
DRY ON/OFF Switch
Selects whether to output the supplied original sound (dry
sound) or not. When set to ON, the original sound is mixed
with the effect (delayed) sound and output from the FT-1Y.
When set to OFF, the original sound is muted and only the
effect sound is fed from the output.
1#
OUT Terminal
Output terminal for the FT-1Y. Connect this output to an
external device such as an effects unit or amplifier.
1$
HOLD (REC) Terminal
External output terminal for the Hold and Rec functions
(when the
REC & REPEAT
switch is turned on). Connect
an unlatch (momentary) type footswitch to this terminal.
1%
MIDI IN Terminal
Input terminal for MIDI signal. This terminal accepts MIDI
signals from an external MIDI device.
1^
MIDI THRU Terminal
Used to output the MIDI signal received at the MIDI IN
terminal to an external MIDI device.
1&
POWER DC12V IN Terminal
Used to connect the dedicated AC adapter supplied with
your FT-1Y.
4-2 Store Presets
If you make a change in a parameter, the lowest preset number’s dot illuminates. This dot does not illuminate when the
current parameter is stored.
To save the changed parameters, perform the following steps.
ex) To change the parameters in Preset 01 and save to Preset 10
Dot showing change in parameter
Press the
STORE
button.
↓
PRESET No. 01 flashes
Use the INC/+ button to show the storing destination preset number 10.
↓
PRESET No. 10 flashes
Press the
ENTER
button to store the setting.
Note: Presets 90–99 are assigned as the factory preset area and users
cannot save their presets here.
4-3 Recall Presets
Presets can be recalled in the following three ways. Select the one most suitable to your application.
• Preset Recall by using TAP-PLAY Footswitch (1):
Press and hold the
TAP-PLAY
footswitch for two seconds.
Release the footswitch when you see the preset number display flash. Each time you press the
TAP-PLAY
switch, the
preset number increments by one. Each time you press the
ON/OFF-STOP
footswitch, the preset number decrements
by one. (The preset number will change at the timing when the footswitch returns to its original position.) When the
desired preset number is shown in the display, press and hold the
TAP-PLAY
footswitch again for two seconds. The
preset is recalled at the timing when the flashing preset number changes to illuminate steadily.
• Preset Recall by using TAP-PLAY Footswitch (2):
It is possible to recall Preset 1 and Preset 2 alternately. For
example, this function is useful if you want to save a short delay in Preset 1 (PS1) and a long delay in Preset 2 (PS2) for
simply switching between them according to phrase being played.
If you press and hold the
TAP-PLAY
footswitch for four seconds when Preset 1 has been recalled, the Preset 1 display
flashes and then Preset 2 is recalled. Similarly if you press and hold the
TAP-PLAY
footswitch for four seconds when
Preset 2 has been recalled, the Preset 2 display flashes and then Preset 1 is recalled.
If you press and hold the
TAP-PLAY
footswitch for four seconds when a preset number other than Preset 1 and Preset
2 has been recalled, the currently displayed preset number flashes and then Preset 1 is recalled.
• Preset Recall via MIDI:
On receiving a program change number MIDI signal from an external MIDI device, the FT-
1Y’s preset will be switched. The MIDI channel on the device sending the program change number and the MIDI channel
on the FT-1Y must be matched. If the FT-1Y’s MIDI channel is set to Omni ([
AL
]), it will accept program change numbers
on all of the MIDI channels and switch its preset accordingly.
4-1 Change Parameters
Each of the sections numbered from
q
to
t
in the figure on page 5 has a tact switch for selection. By pressing the
switch, the section is selected and the displayed numeric value starts flashing. When flashing, the parameter value can
be changed by using the
INC/+
and
DEC/–
switches.
Pressing the tact switch repeatedly changes the indicated items in turn.
ex) Output Section
Tact Switch
INC/+ & DEC/– Switches
OUTPUT LEVEL display (illuminates)
OUT
LED illuminates
↓
Press the tact switch
OUTPUT LEVEL display (flashes)
OUT
LED illuminates
↓
Press the tact switch
FEEDBACK LEVEL display (flashes)
FEEDBACK
LED illuminates
↓
Press the tact switch
DELAY LEVEL display (flashes)
DELAY
LED illuminates
↓
Press the tact switch
OUTPUT LEVEL display (flashes)
OUTPUT
LED illuminates
Содержание FT-1Y
Страница 1: ...OWNER S MANUAL Ver 1 0...