manualshive.com logo in svg

FRC Turbofoam TFC100, Руководство пользователя

Поделиться
Скачать
FRC Turbofoam TFC100 Скачать руководство пользователя страница 57

TFC100 Rev180215

57

Figure L14.  Summing Box Mounting Dimensions

Mounting holes are 

clearance or tapped for #8 

screws.

Install Summing Box (Multiple Flow Sensors Only)

The summing box mounts with four screws. Make sure there is room to connect the cables. The summing 

box is required when there is more than one discharge flow sensor.

1.  Measure and mark mounting location for summing box mounting screw holes. Make sure there is 

clearance for the module and cables before drilling holes. Refer to the Figure 4 for layout and dimensions.

2.  Drill four holes, clearance or tapped, for #8 mounting screws.
3.  Place box in position and secure with four screws.
4.  Connect the cable(s) to the module. (Refer to Wiring Section.)

LED Indicators

Green LED: Flashing when there is no flow input; Steady on when flow input is detected.
Red LED: Flashing indicates that there is a datalink problem; Steady on when there is a conflict with the 

box address setting. 

5.827"

(148mm)

5.295"

(134.5mm)

3.701"

(94mm)

2.628"

(67mm)

1.870"

(48mm)

When more than one summing box is installed, 

the addresses need to set. Remove the four screws 

on the bottom and open the box to access the dip 

switch to change the address setting.

Switch

Address

1

2

Box 1

ON

OFF

Box 2

OFF

ON

Box 3

ON

ON

Содержание Turbofoam TFC100

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды