FRC Turbofoam TFC100 Скачать руководство пользователя страница 21

Страница: 21 / 88

TFC100 Rev180215

PROGRAMMING

Programming functions are allowed when the control module is in the off mode. All program functions are

password protected.

The P-code program functions are available to view and change after the password code has been entered.

Scroll through the P-codes. Use the

PRESET

button to enter the programming mode and select specific values

(number, word, or symbol) to change. The value blinks and the

and

–

buttons are used to change that value.

Note:

To exit programming modes, press and hold the

button for five (5) seconds.

Enter Password for Program Access

Note:

The TFC100 does not have a message display. Information is only shown in the 4-digit display,

procedures are the same. (Substitute

MODE

for

button.)

1. Press and hold the

button for 3 seconds. The

FLOW

display shows four dashes

– – – –

and the

message display shows

ENTER CODES

. Release the button.

2. Press the

and

–

buttons to enter a code. Each time a button is pressed the first digit changes by 1.

Set the first digit to the desired number.

3. Press the

PRESET

button to move the curser to the next digit. Press the

and

–

buttons to change

the digit.

4. Repeat step 3 and enter the password code.
Result: When a correct password code is entered the

FLOW

display flashes the program (P) code and

the message display shows the name of the program or a description of the program code.

5. Press the

and

–

buttons to scroll through the codes.

6. Use the

PRESET

button to enter the programming mode and select specific values to change, the

and

–

are then used to change the value, the

button is used to save the changes.

7. Press and hold the

button for five (5) seconds to exit.

Calibration Passwords 1111 and 1112

Provides access to system programming required for calibration procedures.

1111 - Calibrate Discharge Flow Sensor(s)
1112 - Calibrate Foam Pump

Refer to Calibration Section.

Operator Password 1221

Provides access to system programming P100 codes.

1221 - Operator Programs

Refer to Operator P100 Codes.

Restore Programmed Functions Passwords 5122 and 5123

Provides access to upload all system programming and calibration information from one component to another.

5121 - Initiates Synchronization Between Control Module and Foam Pump Control Programs
5122 - Set/Clear Control Module Restore Flag
5123 - Set/Clear Foam Pump Control Restore Flag

Refer to Restore Programmed Functions Section.

Содержание Turbofoam TFC100

























































































Результаты поиска

Содержание Turbofoam TFC100

Отзывы:

Бренды по названию

Популярные бренды

FRC Turbofoam TFC100, Руководство пользователя

Результаты поиска

Содержание Turbofoam TFC100

Отзывы:

Бренды по названию

Популярные бренды