FRC Turbofoam TFC100 Скачать руководство пользователя страница 18

Страница: 18 / 88

TFC100 Rev180215

Operation Notes

If a tank empty signal goes active the foam pump stops. The pump can be run in override mode by pressing the

ON/OFF

button. The warning stays active, the pump should not be run with no foam concentrate flowing.

If the foam pump motor RPM sensor information is lost the system operates using a pre-programmed plot based

on the current draw of the motor.

If the flow sensor information is lost the system is operated in the manual mode. Refer to Manual Mode.
To complete flushing the system press the

ON/OFF

button. (If the

FLUSH

button is pressed, the system re-starts

auto mode.)

Switching Foam Tanks - Automatic Flush (TFC400 Only)

When the control module is in the auto mode the system performs an automatic flush sequence when switching

between the A foam tank and B foam tank. Discharge water must be flowing to cycle through the flush mode.

When switching from A foam tank to B foam tank the

A/B

button is pressed:

The message display shows

A - - - > B

and status information, the A tank valve closes then the flush valve

opens, the system flushes for the amount of time set in the programming (default is 8 seconds), the flush

valve closes then the B tank valve opens.

When switching from B foam tank to A foam tank the

A/B

button is pressed:

The message display shows

B - - - > A

and status information, the B tank valve closes then the flush valve

opens, the system flushes for the amount of time set in the programming (default is 8 seconds), the flush

valve closes then the A tank valve opens.

Manual Mode

The manual mode is used when flow rate information is not received by the control module. It allows the

operator to manually enter a discharge flow rate for system operations. In the manual mode the foam percent value can

be changed by pressing the

button and using the

and

–

buttons.

Ensure water continuously flows through the discharge during Manual Mode operation.

The manual mode is activated when discharge water is flowing but no flow is indicated in the

FLOW

display.

Note:

Ensure there is foam concentrate in the tank, in manual mode there is no auto shut down of the foam

pump if the tank goes empty.

1. Press both the

+/–

buttons at the same time for 3 seconds to enter manual mode.

Results:

MANUAL MODE

flashes in the message display for 3 seconds, the message display changes to show

USE +/– FOR FLOW

, the

FLOW

display and red LED flashes. (TFC100 flashes the

ON/OFF

LED, the

FLOW

LED is on.)

2. Press the

button and then press

PRESET

+/–

buttons to adjust the

FLOW

FOAM

rates.

Results: The

FLOW

display shows the operator entered flow rate, the system responds to this data and injects the

correct concentrate into the discharge.

3. Press the

button to toggle between setting the flow rate and foam percent value.

Press the

PRESET

button.

Results: The message display changes to show

USE +/– FOR %

, the

FOAM %

display flashes.

(TFC100 the

% FOAM

LED is on.)

Press the

and

–

buttons to set the %.

Press the

button to return to flow rate control.

4. Press the

ON/OFF

button, the LED goes off; this will stop/start the concentrate pump and shuts down the

TurboFoam system. Press the

ON/OFF

button again, the LEDs comes on, the system powers on in the

manual mode.

5. Press both the

+/–

buttons at the same time for 3 seconds to exit manual mode.

NOTE: For the TFC100, substitute

MODE button

for

MENU

button in the procedure steps.

Содержание Turbofoam TFC100

























































































Результаты поиска

Содержание Turbofoam TFC100

Отзывы:

Бренды по названию

Популярные бренды

FRC Turbofoam TFC100, Руководство пользователя

Результаты поиска

Содержание Turbofoam TFC100

Отзывы:

Бренды по названию

Популярные бренды