FRC Turbofoam TFC100 Скачать руководство пользователя страница 13

Страница: 13 / 88

TFC100 Rev180215

Controls and Indicators

All controls and indicators are located on the front of the control module. It contains the push button electronic

controls, LEDs, and digital displays. (Refer to figure.) The buttons are used for operations, reviewing stored data,

and during programming. See Operation and Programming Sections for more information.

ON/OFF

Button

Press and hold this button for three seconds to turn the system on. LED goes on. The

WATER FLOW

display

shows discharge flow rate. A remote ON/OFF switch is available as an option.

PRESET

Button

Press this button to set the % foam to a pre-programmed value.

+ / –

Buttons

Press the

increase or

–

decrease buttons to raise or lower the amount of foam concentrate (% foam) that

is mixed into solution. The

display shows the selected percent.

MODE

Button (TFC100 Only)

Used to toggle the display mode. A mode LED goes on to indicate the selected display mode. Sets totals to 0.

Mode LEDs (TFC100 Only)

The four LEDs indicate the display mode for the 4-segment display;

%FOAM, TOTAL FOAM, FLOW,

and

TOTAL WATER

FOAM EMPTY

LED (TFC100 Only)

The input from a TankVision Pro or foam tank level indicator drives this LED.

FOAM %

Display

The display shows the selected percent of foam concentrate in the discharge foam solution.

A/B

Button (TFC400 Only)

Used to select the A foam or B foam tank. The

FOAM A

FOAM B

LED goes on for tank selected. When

this button is pressed (with the system is on) a flush cycle automatically occurs before the electric valve switches

the tank (there must be water flow through the discharge).

FLUSH

Button (TFC300/400 Only)

Used to operate the flush (or prime) mode. The LED blinks when flush mode is active (there must be water

flow through the discharge).

MENU

Button (TFC200/300/400)

Used to access system detailed information, stored data, and program features. Sets totals to 0.

Message Display (TFC200/300/400)

The two line multifunction display shows system information.
When the

button is pressed, during calibration, or during programming the display shows codes,

stored data, and program functions.

FLOW

Display

The display shows discharge water flow rate through the discharges. In manual mode it shows operator

entered flow rate.

Содержание Turbofoam TFC100

























































































Результаты поиска

Содержание Turbofoam TFC100

Отзывы:

Бренды по названию

Популярные бренды

FRC Turbofoam TFC100, Руководство пользователя

Результаты поиска

Содержание Turbofoam TFC100

Отзывы:

Бренды по названию

Популярные бренды