Franklin Electric SubDrive100 Скачать руководство пользователя страница 21

Страница: 21 / 24

Accessories

Pressure Sensor Kit

- replacement sensor with 10 ft of 22 AWG cable and sensor

adjustment tool:

223 995 901

(SubDrive75/100/150)

Sensor Cable Kit

- 100 feet of 22 AWG pressure sensor cable:

223 995 902

(SubDrive75/100/150,)

Input Filter

– filter used on the input side of drive to help eliminate interference:

225 198 901

(SubDrive75/100/150)

Output Filter

– filter used on the output side of the drive to help eliminate interference:

225 300 901

(SubDrive75/100/150,)

Surge Capacitor

– capacitor used on the service panel to help eliminate power interference:

225 199 901

(SubDrive75/100/150)

SubDrive75 N1 Fan Kit

– replacement fan for SubDrive75 with 80 mm (3.15 in) fan:

225 635

905

SubDrive75 N1 Fan Kit

– replacement fan for SubDrive75 with 92 mm (3.62 in) fan:

225 635

908

SubDrive100/150 N1 Fan Kit

– replacement fan for SubDrive100/150 with 80mm (3.15 in)

fan:

225 635 907

SubDrive100/150 N1 Fan Kit

– replacement fan for SubDrive100/150 with 92 mm (3.62 in)

fan:

225 635 909

Technical changes without notice / Techn. Änderungen vorbehalten / Modifications techniques réservées sans préavis / 5930

Содержание SubDrive100

























Результаты поиска

Содержание SubDrive100

Отзывы:

Бренды по названию

Популярные бренды

Franklin Electric SubDrive100, Руководство по установке

Результаты поиска

Содержание SubDrive100

Отзывы:

Бренды по названию

Популярные бренды