manualshive.com logo in svg

Franklin Electric SubDrive100, Руководство по установке

Поделиться
Скачать
Franklin Electric SubDrive100 Скачать руководство пользователя страница 17

Wiring Connections

Serious or fatal electrical shock may result from failure to connect the motor, the SubDrive, metal plumbing and 

all other metal near the motor, or cable to the power supply ground terminal, using wire no smaller than motor 

cable wires. To reduce risk of electrical shock, disconnect power before working on or around the water system.

Do not use motor in swimming areas.

1.  Verify that the power has been shut off at the main 

breaker.

2.  Verify that the dedicated branch circuit for the SubDrive is 

equipped with a properly-sized circuit breaker.

3.  Use appropriate strain relief or conduit connectors.
4.  Remove the SubDrive lid.
5.  Feed the motor leads through the opening on the bottom 

right side of the unit and connect them to the terminal block positions marked GND (Green/Yellow Ground 

Wire), Black, Brown, Grey (Figure 3).

Output to Motor

Blk  Brw Gry

(Output)

Figure 3: Motor Lead Connections

For retrofit application , make sure to check integrity of power and motor leads.

This requires measuring the insulation resistance with the suitable megohmmeter.

WARNING

DANGER

Figure 4: 

Power and Pressure Sensor 

Connections

8.  Verify that the SubDrive unit is properly configured for the horsepower rating of the motor and pump being used. 

(See the section on Pump Sizing for information on Drive Configuration pg. 6- 8.)

9.  Replace the cover. Do not over-tighten the screw.

Power Leads

1

2

Pressure Sensor

Leads

Black

Red

L2

From Power Source

L1

(Input)

L2

Sensor 

Connection

6.  Feed the 230 VAC power leads through the larger opening on the bottom left side of 

the SubDrive controller and connect them to the terminals marked L1, GND, and L2 

(Figure 4).

7.  Use the smaller opening on the bottom left side of the SubDrive unit and connect 

the red and black leads to the terminals marked “1” and “2” (interchangeable) with a 

small screwdriver (provided). 

 

Note:

 A 3 m section of pressure sensor cable is provided with the controller, but it 

is possible to use similar 0,33 mm² wire for distances up to 30 m  from the pressure 

sensor. A 30 m section of pressure sensor cable is available from your local Franklin 

Electric distributor. (See Accessories)

15

Technical changes without notice / Techn. Änderungen vorbehalten / Modifications techniques réservées sans préavis / 5930

Содержание SubDrive100

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды