Framers Corner M3 Скачать руководство пользователя страница 12

Страница: 12 / 19

Page 12

Fault

Cause

Remedy

edges not fully inserted into moulding -

Light does not illuminate

Pedal stroke incomplete

Press pedal until the light illuminated

Top clamp set too high

Set gap between moulding and pressure pad

to not more than 20mm

edges not fully inserted into moulding -

Light does illuminate

Microswitch actuating screw requires adjust-

ment, Part 67

Loosen locking nut on screw and adjust so

that indicator lights when wedge driver is flush

with the top surface of the table

edges being driven in too deep

Driver limiter not set correctly

Reset the adjusting screws

Attempt at stacking fails

Fence is moving during cycle

Lock the fence when stacking (see page 7)

Stacking wedges break through side of

moulding

Stack is too high

Use less or smaller size wedges

edge position too close to edge

Move the wedge position away from the edge

avy grain wood (particularly hardwood)

The wood species is not suitable for stacking

edge deforms when inserted

Hardwood

Use specific hardwood wedges

Driver does not return after cycle

Driver has come out of holder

Refit the driver into the holder (see page 10)

Top clamp does not return to start position

Top clamp not set correctly

Set gap between moulding and pressure pad

to not more than 20mm

edge inserted light does not Illuminate

Battery Flat

Replace Battery - access from front, under the

table at rear

Содержание M3




















Результаты поиска

Содержание M3

Отзывы:

Бренды по названию

Популярные бренды

Framers Corner M3, Руководство оператора

Результаты поиска

Содержание M3

Отзывы:

Бренды по названию

Популярные бренды