Framers Corner M3 Скачать руководство пользователя страница 11

Страница: 11 / 19

TROUBLE SHOOTING GUIDE

Page 11

Fault

Cause

Remedy

edges are too wide to load into the maga-

zine

rong type of wedges

Only Universal type 10.3mm wedges can be

used

Faulty wedges

Check with wedge supplier

No wedge is inserted into the moulding

The wedge magazine is empty

Reload the magazine

edge feeder spring is not engaged

Release the nylon cord, check the push spring

is moving freely

edge is jammed in cap

Clear the blockage (see page 10)

Fence does not slide

Build up of dirt

Lubricate the two sliding fence bars (part no.

45)

Top clamp is marking the moulding

rong pressure pad fitted

Change to alternate shape pad

Pressure pad is worn or damaged

Replace pad

Bad joint - Open joint

Bad mitre

Check mitring machine

Moulding moving during pinning

Ensure the base of the moulding is flat

Move the wedge position away from the back

edge

Moulding is moving during pinning

Cap not flush with table

Remove cap and refit it (see page 10)

Extension tables not flush with table

Reset the tables

Top clamp not set correctly

Set gap between moulding and pressure pad

to not more than 20mm

Front clamp not set correctly

Set gap between moulding and clamp to not

more than 15mm

Содержание M3




















Результаты поиска

Содержание M3

Отзывы:

Бренды по названию

Популярные бренды

Framers Corner M3, Руководство оператора

Результаты поиска

Содержание M3

Отзывы:

Бренды по названию

Популярные бренды