manualshive.com logo in svg

frako PQM 1588, Руководство по эксплуатации

Поделиться
Скачать
frako PQM 1588 Скачать руководство пользователя страница 24

24

  7.3.2 Configuration: firmware update

A firmware update can be carried out either in SYSTEM-SW or at the instrument website. 
To carry out a firmware update, use the 

Search

 button to select a firmware file with the format 

PQM1588_FIRMWARE_V01.XX.YY_rZZZZZZZ.zip, then click the 

OK

 button to start the update. 

This process can take several minutes. After the time indicated has expired, the website can be 
updated. If the update has been successful, the new version of the PQM firmware is stated against 

Firmware Release

 in the table (see below).

 
 
 
 
 
 
 

 
 
Figure 8   
Firmware update

NOTE! 
The configuration function described in this section 

[7.3.2 Configuration: Firmware 

update]

  is available for software version 1.26.70 or later.

  7.3.3 Service functions: OPC-UA

On this page the PQM 1588 service functions and applications can be enabled and disabled.
After one or more service functions have been enabled or disabled, the 

Send configuration

 but-

ton must be clicked to complete the configuration process.

 

Figure 9   
Service functions: OPC-UA

NOTE! 
The function described in this section 

[7.3.3 Service functions: OPC-UA]

  is availa-

ble for software version 1.26.70 or later.

Содержание PQM 1588









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды