background image

3

27

Advanced Chipset Features

► Memory Configuration / DRAM Timing Configuration

Press <Enter> to go to its submenu.

    

 

The following six items display the values configured at the settings of "DRAM Timing Mode".

► CAS Latency

This item shows the CAS latency. The CAS Latency is the number of clock cycles that elapse
from the time the request for data is sent to the actual memory location until the data is trans-
mitted from the module.

► RAS / CAS Delay

This item displays a delay time (in clock cycles) between the CAS and RAS strobe signals.

► Row Precharge Time

This item shows the number of clock cycles taken between issuing of the precharge command 
and the active command. The DRAM row precharge time is in unit of clock cycle.

► Min Active RAS

Displays the number of clock cycles taken between a bank active command and issuing of the 
precharge command.

► RAS / RAS Delay

This item

 

displays a delay time (in clock cycles) between the RAS and RAS strobe signals.

► Row Cycle

This item shows the minimum timing interval between successive active commands to the 
same bank. The row cycle time is in unit of clock cycle.

CMOS Setup Utility - Copyright (C) 1985-2006, American Megatrends, Inc.

Advanced Chipset Features

  Northbridge Chipset Configuration   

 

        Help Item

 

  ► Memory Configuration 

 

 

[Press Enter]

 

 

   

  ► DRAM Timing Configuration

   

[Press Enter]

 

         

   

   

CAS Latency 

 

 

:N/A , 6 CLK  

         

 

   

RAS/CAS Delay    

 

:N/A , 6 CLK

    Row Precharge Time   

:N/A , 6 CLK 

         

    Min Active RAS    

 

:N/A , 15 CLK  

     RAS/RAS Delay    

 

:N/A , 4 CLK

    Row Cycle 

    

:N/A , 21 CLK

      

   ↑↓←→:Move   Enter:Select     +/-/:Value     F10:Save      ESC:Exit     F1:General Help         

                                                F9:Optimized  Defaults

[Press Enter]

Содержание A78AX 3.0 Series





































































































Отзывы: