Foundry Configuration Guide for the FESX, FSX, and FWSX
20 - 18
© Foundry Networks, Inc.
December 2005
FESX424 router# show ip ospf interface
v20,OSPF enabled
IP Address 1.1.20.4, Area 0
OSPF state BD, Pri 1, Cost 1, Options 2,
Type non-broadcast
Events 6
Timers(sec): Transit 1, Retrans 5, Hello 10, Dead 40
DR: Router ID 1.1.13.1 Interface Address 1.1.20.5
BDR: Router ID 2.2.2.1 Interface Address 1.1.20.4
Neighbor Count = 1, Adjacent Neighbor Count= 2
Non-broadcast neighbor config: 1.1.20.1, 1.1.20.2, 1.1.20.3, 1.1.20.5,
Neighbor: 1.1.20.5
Authentication-Key:None
MD5 Authentication: Key None, Key-Id None, Auth-change-wait-time 300
In the Type field, “non-broadcast” indicates that this is a non-broadcast interface. When the interface type is non-
broadcast, the Non-broadcast neighbor config field displays the neighbors that are configured in the same sub-
net. If no neighbors are configured in the same sub-net, a message such as the following is displayed:
***Warning! no non-broadcast neighbor config in 1.1.100.1 255.255.255.0
Assign Virtual Links
All ABRs (area border routers) must
have either a direct or indirect link to the OSPF backbone area (0.0.0.0 or 0).
If an ABR
does not have a physical link to the area backbone, the ABR can configure a
virtual link
to another
router within the same area, which has a physical connection to the area backbone.
The path for a virtual link is through an area shared by the neighbor ABR (router with a physical backbone
connection), and the ABR requiring a logical connection to the backbone.
Two parameters fields must be defined for all virtual links—transit area ID and neighbor router.
•
The
transit area ID
represents the shared area of the two ABRs and serves as the connection point between
the two routers. This number should match the area ID value.
•
The
neighbor router
field
is the router ID (IP address) of the router that is physically connected to the
backbone, when assigned from the router interface requiring a logical connection. When assigning the
parameters from the router with the physical connection, the router ID is the IP address of the router requiring
a logical connection to the backbone.
NOTE:
By default, the Foundry router ID is the IP address configured on the lowest numbered loopback
interface. If the Layer 3 Switch does not have a loopback interface, the default router ID is the lowest numbered IP
address configured on the device. For more information or to change the router ID, see “Changing the Router ID”
on page 16-23.
NOTE:
When you establish an area virtual link, you must configure it on both of the routers (both ends of the
virtual link).
Содержание FastIron Edge Switch X424
