TM
41
TM
Fig. 1
Fig. 2
Fig. 3
Fig. 2B
Fig. 2A
FT 3309
WARNING:
•
Modules FT4660 normally function as main external unit
(timed engaged signal).
To set them as secondary external unit (engaged signal
active for the whole time the riser is in use), it is necessary to
put all the Dip switches of the selector to ON.
• When a call is transmitted from the external unit if a busy tone
is heard instead of the ring tone it means that a call to
another external unit is in session.
• In case of a persistent shortcircuit on the bus line an
intermittent signaling sound will be heard on the external
unit.
1.
Connect the terminal boards of modules FT3323/3, FT3323/4
and FT3323/6 together and with the terminal board of the
FT4660 group using the special cables. Insert the modules
FT3323/3, FT3323/4 and FT3323/6 on the relative terminal
boards (figure 1).
2.
On the terminal board of module FT4660 connect the power
supply to ~~ , set the switch in programming position (red)
(Figure 2A).
Connect the terminal board to module FT4660 assembled as
shown previously.
(Warning - modules FT3323/3, FT3323/4 and FT3323/6 to be
programmed must already be positioned) (figure 2).
Note:
for connection between the terminal board and module
FT4660, it is possible to use the cable FT3309, available as
an optional accessory (figure 3) during the programming
stage.
3.
Set the Dip switches located on the rear of the audio module
with the same code assigned to the telephone or monitor
according to the correspondence described in the
programming table on page 42.
4.
Press the push-button to be associated with the telephone
call. A confirmation tone signals that programming has taken
place.
5. After completing programming, set the switch back into
standby position (white) (Figure 2B).
Push button programming with audio-video FT4660 group and modules FT3323/3, FT3323/4 and FT3323/6
Содержание DIGI-2
