fortessa DIGI-2, Техническое руководство

Страница: 28 / 80

TM 26
Standard combined access FT3328 and vandal
combined access FT3188 electronic digital key
General information
The range of electronic standard combined access keypads
consists of 2 models:
• FT3328 for insertion in the standard modular push-button panels
for the creation of mixed systems with access control -audio and
video door entry systems or to be used stand-alone.
• FT3188 for insertion in the vandal resistant modular push-
button panels for the creation of mixed systems with access
control -audio and video door entry systems or to be used
stand-alone.
Technically speaking FT3328 and FT3188 come complete with 2
relays which can be controlled with different codes.
Warnings
- Carefully read and follow the instructions given by the
manufactured.
- All the equipment making up the installation must only be used
for the purpose it was built for.
- Install the equipment in compliance with the legislation in force.
- In case of a fault and/or incorrect operation of the equipment,
disconnect it from the power supply and do not tamper with it.
For any repair work, only contact a technical service center
authorized by the manufacturer.
- Connect to the ground electronic key FT3328 and electronic key
FT3188 like showed on page 27.
FORTESSA reserves the right to change the characteristics and
dimensions of the equipment without prior warning.
Technical characteristics
• Total no. Of codes available: 302
- one supercode;
- 300 relay codes. The total number of codes available can be
distributed as desired between relay 1and relay 2. E.g.: 245
different codes for relay 1 and 55 different codes for relay 2;
- anti-panic code.
• Outputs available: 2 on independent relays according to the
models, plus 2 open collectors (1 for FT3328).
• Operation of output relays: either bistable or monostable;
programmed from the keypad.
• Monostable mode: programmable impulse between 1 and 99
secs. approx.
• Length of supercode: from 1 to 8 repeatable digits.
• Lenght of relay codes: from 1 to 8 repeatable digits.
• Length of anti-panic code: 1 digit.
• Input for remote reset (for FT3188 only).
• Remote input for enabling of ‘’key’’ push button (for FT3328 only).
• Programming input.
• Operation mode input with one button only (time programmer).
• 3 signalling LEDs depending on the model 2 for indication of
closure of the relays and 1 to indicate the state of programming.
• NO - NC outputs free of potential.
• Contact capacity: 10 A non-inductive.
• Service outputs: max 500 mA.
• Power supply: 12V AC/DC.
• Absorption: 250mA 12V AC with 3 working relays.
• Operation temperature: from -10°C to + 50°C.
Programming and functioning modes
There is a time limit for programming after which the operation is
cancelled (approx. 40 secs. between pressing one button and the
next): for this reason the procedure should only be started when the
operator has a clear idea of all the operations to be carried out.
1) Insertion of supercode
Programming of the supercode is the first operation to be performed
since it subsequently affects all the other stages. It is a good idea to
choose a short, easy-to-remember code.
Write the number on a piece of paper and keep it in a safe place.
Precedure for entering supercode
1) Connect power to the keypad.
2) Make the bridge between PGM and the negative (– or
CK2 ).
3) Check that the red LED is on.
4) Key in the supercode (1 to 8 repeatable digits).
5) Press button “E” on the key-pad to memorise the code entered.
6) Wait 10 seconds or a confirmation tone.
7) Remove the bridge.
E.g. to insert supercode 12345, proceed as follows:
- give power supply;
- make the bridge;
- key in the following: 12345 E;
- wait 10 sec. or a confirmation tone; remove the bridge.
FT3328
FT3188
E
1 2 3
6 5 4
7 8 9
0
1 2 3 4
5 6 7 8
9 0 E