Fort WM 600 B, Эксплуатация и обслуживание

Страница: 27 / 36

27
impediments of any kind.
- The operator must immediately release the levers
that actuate the machine if a person or an animal
access the danger of the machine and wait, befo-
re resuming the work, that the area is completely
free.
- Never leave the machine in motion especially for
long periods; in this way, you also avoid that the
belt that rotates the cutting device can damage.
- When a person is exposed, that is within the
«dangerous area», the operator shall immediately
intervene and stop the machine to send away the
above person.
- Never leave the machine while it is running.
- Periodically check the integrity of the machine on
the whole and the protection devices.
- Before carrying out any repair or maintenance
operation on the machine, stop the machine and
shut the engine off.
- In case the guards were removed, make sure to fix
them in place before using the machine again.
- Comply with the suggested oils. Keep the lubricants
away from children. Carefully read the warnings and
the precautions listed in the lubricant containers.
After using them, wash your hands thoroughly.
Dispose of the used lubricants according to the
antipollution regulations.
- At the end of the maintenance and repair operations,
make sure that all operations are completed, that
the safety devices and the guards are back in place
before starting the machine again.
- The spare parts must correspond to the needs
established by the Manufacturer. Use only genuine
spare parts
- When working on yielding grounds, near slopes,
ditches or steep grounds, operate with the utmost
care at low speed to prevent the machine from over-
turning; it is moreover suggested, in these cases,
to arrange the load as further down as possible to
give the machine more balance
- In case the machine is meant to work on raised
grounds or near precipices, before starting to work,
it is compulsory to suitably put barriers around all
tracts that may involve the fall of the machine from
above due to a possible wrong maneuver by the
operator.
- It is forbidden to transport loads weighing higher
than the machine max. carrying capacity.
- Avoid, if possible, to cut the grass when it is wet;
becomes high danger of slipping especially when
working on steep slopes.
- It is absolutely forbidden to touch the running
parts or to come between them. (in particular the
crawlers) by keeping at a safety distance.
- It is absolutely forbidden to have foreign persons
stand within the machine working area.
- Avoid parking the machine on a slope. If necessary,
block the machine with logs or suitable stones to
be placed between the ground and the crawlers.
- During the maintenance operations, do not operate
the machine in poorly ventilated rooms: the exhaust
gases are harmful to the health.
- Periodically check the tightening of the screws, nuts
and couplings, if any.
- It is absolutely forbidden to remove or tamper the
safety devices.
- The maintenance of the machine shall be performed
by skilled personnel only after shutting the engine
off, by following the instructions of this manual and
of the engine manual
- Before refueling or topping up with oil, stop the
engine and to let it cool down.
While refueling, do not smoke and do not get near
free flames. Be sure to thoroughly wipe the spilled
gasoline before starting the engine.
- If any part clogs or stops, stop the engine and then
remove the foreign body.
- Before turning, disengage the differential lock (for
machines that are equipped).
- THE BRAKING SYSTEM OF THE CUTTING DEVI-
CE, CONTROLLED BY LEVER 3 IN FIG. 1, STOPS
THE ROTOR WITH THE KNIVES IN A FEW SECON-
DS BUT NOT IMMEDIATELY. WHEN YOU RELE-
ASED THE LEVER, YOU SHOULD, THEREFORE,
LEAVE THE DRIVING SEAT ONLY AFTER THAT
THE CUTTING DEVICE IS PERFECTLY STOPPED.
- APPROACH THE CUTTING DEVICE ONLY WHEN
THE ENGINE IS OFF AND WHEN ALL THE ITEMS
ARE PERFECTLY STOPPED.
SECTION 3
Transport
3.1 TRANSPORT
The machine is packed in cartons. In case it is stored,
we suggest not to put more than three cartons of the
same type one on the other (1+2).
Do not put a load of more than 200 kg (with base
support not less than that of the packaging itself) on
one single carton.
Remember that the packaging materials are recyclable
ENGLISH