Fort F 51, Эксплуатация и обслуживание

Страница: 17 / 28

17
DESCRIPTION OF FIGURES
Fig. 1 F51 - Main components.
1) Identification plate.
2) Label with serial number.
3) Screw for locking / unlocking steering handles.
4) Steering handles.
5) Register cable lever forward.
6) Register cable lever reverse.
7) Accelerator lever.
8) Device locking / unlocking lever reversing
control.
9) Command reversing lever (red color)
10) Device locking / unlocking lever forward control.
11) feed control lever (black color)
12) Protective casing.
13) Fuel filler cap in the tank.
14) Spur.
15) Jack of small wheel locking.
16) Small wheel.
17) Rotor hoes group.
18) Tamping disk.
19) Hand lever a pull starter.
20) Device choke fuel.
21) Engine stop switch.
Fig. 2 - Overall dimensions.
Fig. 3 - Lifting the machine and its attachment
points.
Fig. 4 - milling Group.
- 1) Tamping disk. - 2)
Spring pin. - 3) Group Single hoe. - 4) Hoes Group
doubles. - 5) Jack locks hoes.
Fig. 5 - Dimensions of the milling group (as a fun-
ction of the arrangement of tines).
Fig. 6 - Wheel position. - 1) Small wheel.
Fig. 7 - Carter belt. - 1) Fixing screw carter. - 2)
Jack spur.
Fig. 8 - Engine fixing. - 1) Mounting bolts.
Fig. 9 - The engine is loose. - 1) Mounting bolts.
Fig. 10 - Lubrication chain. - 1) Grease fitting.
Fig. 11 - Signals of security and their position on
the machine
(for their description see item 2.2 Sa -
fety Signs).
ENGLISH
TABLE OF CONTENTS
SECTION 1. Description and characteristics of the
machine
1.1 Foreword ........................................................ 18
1.2 Warranty ........................................................ 18
1.2.1 Warranty exclusions ....................................... 18
1.3 Machine identification .................................... 19
1.4 Machine description and intended use ........... 19
1.4.1 Use of the machine ......................................... 19
1.4.2 Unauthorized use of the machine ................... 19
1.4.3 Control and driving position ........................... 20
1.5 Protections and safety devices ....................... 20
1.5.1 Noise level ...................................................... 20
1.5.2 Vibration level ................................................. 20
1.6 Technical features .......................................... 20
SECTION 2. Safety and prevention
2.1 Safety ............................................................. 20
2.1.1 Terminology used ........................................... 21
2.1.2 General safety standards ................................ 21
2.2 Safety signals ................................................. 21
2.3 Safety while operating and maintaining the
machine .......................................................... 22
SECTION 3. Transport
3.1 Transport........................................................ 23
SECTION 4. Use
4.1 Before use ...................................................... 23
4.1.1 Adjusting of the handlebars ............................ 23
4.1.2 Milling group .................................................. 23
4.1.3 Milling bonnet ................................................ 24
4.1.4 Spur ............................................................... 24
4.1.5 Small wheel .................................................... 24
4.1.5 Preliminary chechs ......................................... 24
4.2 Starting ......................................................... 24
4.3 In work ........................................................... 24
4.3.1 Using the machine on slopes ......................... 25
4.3.2 Parking ........................................................... 25
4.4 Stopping of the engine ................................... 25
4.5 After use ......................................................... 25
SECTION 5. Routine maintenance
5.1 General information ........................................ 25
5.2 Engine maintenance ....................................... 25
5.3 Machine maintenance ..................................... 26
5.3.1 Recording control lever forward and reverse . 26
5.3.2 Adjustment of the accelerator control ............ 26
5.3.3 Belt replacement ............................................. 26
5.4 Extraordinary maintenance ............................. 26
5.5 Setting at rest ................................................. 26
5.6 Machine dismantling ...................................... 26
5.7 Spare parts ..................................................... 26
Declaration of conformity .......................................... 27