manualshive.com logo in svg

Ford Focus RS 2016, Техническое обслуживание и тренинг

Поделиться
Скачать
Ford Focus RS 2016 Скачать руководство пользователя страница 78

The terminating resistors of the HS-CAN multimedia
system are located in the IPC (instrument panel cluster)
and in the ACM (audio front control module).

The HS-CAN multimedia bus signals can be picked off
via pins 1 and 8

The RCM (restraints control module) is connected to
the CAN module via a private HS-ABS (anti-lock brake
system) bus. Two separate termination resistors are
installed here.

The MS CAN bus terminating resistors are located in
the IPC and the BCM. The total resistance can be
measured at the DLC between pins 3 and 11 and should
be 60 ohms.

E224838

Two modules are designed as gateways:

•

The BCM between the HS-CAN and MS-CAN

•

The IPC between the MS-CAN and HS-CAN
multimedia

Module acronyms:

•

ACM (audio front control module)

•

DSP (audio digital signal processing module)

•

EFP (electronic (finisher panel)

•

APIM (SYNC module)

•

IPC (instrument panel cluster)

•

PDM (passenger door module)

•

DDM (driver door module)

•

HVAC (heating, ventilation and air conditioning)

•

GPSM (global positioning system module)

•

RFA (remote function actuator)

•

RFR - RF receiver (radio receiver for keyless locking
system)

•

BCM (body control module

•

FDSM (front distance sensing module)

•

PAM (parking assist control module)

•

PSCM (power steering control module)

•

ICM (information center module)

•

SASM (steering angle sensor module)

•

HCM (headlamp control module)

•

PCM (powertrain control module

•

RCM (restraints control module)

Service Training

76

Lesson 4 – Electrical

Communications Network

Содержание Focus RS 2016




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды