Ford Focus RS 2016 Скачать руководство пользователя

Страница: 15 / 83

Service Points

2.3L EcoBoost

E215066

Coolant reservoir

Oil dipstick

Oil filler cap

Brake fluid reservoir

Battery

BJB (battery junction box)

Air cleaner housing

Air conditioning connection

Windshield washer reservoir

Transport Mode

Transport Mode Deactivation

After vehicle build, some vehicle modules are set in
Transport mode including the IPC and the BCM.

Transport mode reduces battery drain during longer
periods where the vehicle is not used.

While in transport mode, the IPC displays TRANSPORT
MODE CONTACT DEALER in the message center.

Various systems may be altered or are disabled when
in the transport mode. The vehicle automatically reverts
to normal operation mode after being driven for more
than 201 km .

The vehicle can be manually taken out of Transport
mode using the following procedure.

Deactivation Using Passive Key

1. Place the ignition in the OFF position

2. On vehicles with Push-Button Start, place a

programmed passive key in the PATS backup
starting location. Place the ignition in the ON
position

Service Training

(G1821202)

Lesson 1 – General Information

Содержание Focus RS 2016




















































































Результаты поиска

Содержание Focus RS 2016

Отзывы:

Похожие инструкции для Focus RS 2016

Бренды по названию

Популярные бренды

Ford Focus RS 2016, Техническое обслуживание и тренинг

Результаты поиска

Содержание Focus RS 2016

Отзывы:

Похожие инструкции для Focus RS 2016

Бренды по названию

Популярные бренды