manualshive.com logo in svg

Ford Focus RS 2016, Техническое обслуживание и тренинг

Поделиться
Скачать
Ford Focus RS 2016 Скачать руководство пользователя страница 70

The Focus RS has also has three auxiliary gauges located
on top of the instrument panel to display additional
engine information:

•

Oil temperature gauge - Displays engine
temperature

•

Turbo boost gauge - Displays the added intake
system pressure provided by the turbocharger

•

Oil pressure gauge - Displays engine oil pressure

– If the needle enters the red section a warning lamp

illuminates and a message appears in the
information display

Drive Modes

E224150

1

2

Drive mode switch

1

Drive mode information in information display

2

The Focus RS has four drive modes that can deliver
driving experiences through a suite of sophisticated
electronic systems. Each mode has preset vehicle
management settings to optimize:

•

Steering

•

All Wheel Drive (AWD)

•

Torque vectoring

•

Powertrain response

•

Suspension and.

•

Traction and electronic stability control

There is a drive mode switch located beside the gearshift
lever, which is used to select the desired drive mode.
Pressing the button repeatedly will enable the driver to
scroll through all available modes which are displayed
in the message center.

When the desired mode appears in the message center,
pressing the OK button on the steering wheel selects it.
The four drive modes and their features are listed below:

•

Normal - Default setting each time the vehicle is
started. Vehicle response tuned for street driving,
where the Electronic Stability Control and Traction
Control systems are fully enabled

•

Sport - Vehicle response tuned for performance
street driving, where the Traction Control system is
disabled while the Electronic Stability Control
system remains fully enabled

•

NOTE: This mode is for track use only.

Track - For aggressive driving while at race circuits,
where the system allows greater wheel spin and
limited drift limits. Electronic Stability Control and
Traction Control systems are disabled

•

NOTE: This mode is for track use only.

Service Training

68

Lesson 4 – Electrical

Instrument Panel Cluster (IPC)

Содержание Focus RS 2016




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды