Force Computers PENT/CPCI-721 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 126

background image

Installation

Hardware Upgrades and Accessories

PENT/CPCI-721

2 - 19

IDE Devices

It is possible to connect up to four IDE devices to the PENT/CPCI-721:

• As a factory option, a 16 MByte flash disk can be installed to the pri-

mary IDE port.

• A HD accessory kit can be installed to the primary IDE port via the

on-board connector.

Before connecting IDE devices to the primary or secondary IDE port:

1. Check for IDE devices already connected to the IDE interface

2. Decide which IDE device should be master and which should be

slave

3. Check for switch settings and change configuration if necessary

Note: If connecting a device to the secondary IDE port, make sure
that the length of the ribbon cable does not exceed 0.45 m (18 inches).

At the first boot after connecting an IDE device, modify the BIOS
parameters in setup ( see the “Boot Configuration” section on page 4-6).

SCSI Device Connection

8-bit or 16-bit SCSI devices can be connected to the PENT/CPCI-721.
Before connecting a SCSI device check the SCSI termination and set the
respective PENT/CPCI-721 switch appropriately ( see “Action Plan” on
page 2-10).
At the first boot after connecting a SCSI device check that the SCSI ID of
the device to be installed is not in conflict with the IDs of already
installed SCSI devices.

«
...
57
58
59
60
61
...
»

Содержание PENT/CPCI-721































































































































Отзывы:

Нет отзывов

Похожие инструкции для PENT/CPCI-721

Бренд: Gallagher Страницы: 11

Бренд: U-Prox Страницы: 4

Trailscout 11-9500

Бренд: Bushnell Страницы: 44

Бренд: FingerTec Страницы: 4

Бренд: IDTECK Страницы: 12

Бренд: Ziatech Corporation Страницы: 94

NexXxoS GPX-A 280 M06

Бренд: Alphacool Страницы: 2

Бренд: ACT Страницы: 2

Бренд: Commell Страницы: 23

Бренд: Citizen Страницы: 107

Бренд: Lava Страницы: 1

Lava SSerial-550

Бренд: Lava Страницы: 4

Бренд: Spectrum Страницы: 136

Бренд: Motorline Страницы: 2

Бренд: LSI Страницы: 2

Бренд: Addonics Technologies Страницы: 2

ADA16-32/2(PCI)F

Бренд: Contec Страницы: 109

Бренд: Access Interfacing Solutions Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды