Fondital minorca kr Скачать руководство пользователя страница 9

Страница: 9 / 64

Instructions for the user

Ref.

Description

Steady on

Flashing

Alphanumeric indicator

Temperature, parameter values and

fault indication.

Not used.

Parameter indicator

Indication of "parameter" inside the

parameter menu.

Not used.

Flame lighting indicator

Lit flame indication.

Not used.

Central heating indicator

CH function activated.

Display of CH temperature set-point

or function in progress.

RESET indicator

It is possible to reset the boiler.

Not used.

Parameter editing indicator

During parameter editing, the wrench

symbol stays on until the set datum is

confirmed.

When edited parameter value is

confirmed.

Flue cleaning function indicator

(for the installer)

Flue cleaning function in progress.

Indicates that you are accessing the

flue cleaning function.

DHW indicator

DHW function activated.

Display of DHW temperature set-

point or DHW function in progress.

Содержание minorca kr

































































Результаты поиска

Содержание minorca kr

Отзывы:

Похожие инструкции для minorca kr

Бренды по названию

Популярные бренды

Fondital minorca kr, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание minorca kr

Отзывы:

Похожие инструкции для minorca kr

Бренды по названию

Популярные бренды