Fondital minorca kr Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 64

background image

15

Instructions for the user

1.4.2

Shut-down due to overheating

Fault code E02 is shown on the LCD display in the event of flow water temperature overheating. Contact a service centre or a qualified service
engineer to carry out the maintenance.

1.4.3

Shut-down due to incorrect air/flue gas system draught

The boiler is equipped with a safety device for flue gas exhaustion check.
Should an air/flue gas system malfunction occur, the control device will shut-down the boiler by interrupting the gas supply to the boiler and
the LCD will display the E03 code.
In this case, contact a Service Centre or a qualified service engineer to carry out the maintenance.

1.4.4

Shut-down due to low water pressure

Fault code E04 is displayed on the LCD display in the event of shut-down triggered by the water pressure switch.
Fill the system by working on filler cock (A) (see Fig. 2 Filler cock).
Water pressure must be 1÷1.3 bars while the boiler is cold.
In order to restore water pressure, proceed as follows:

•  Turn the filler cock anticlockwise to allow water to enter the boiler;
•  Keep the filler cock open until the pressure gauge shows a value of 1÷1.3 bar;
•  Turn cock clockwise to close it.

Should boiler shuts down frequently occur it means there is boiler malfunction in progress. Contact qualified personnel or an authorised
service centre for maintenance.

DANGER

Make sure you close filler cock (A) carefully after filling procedure is completed.
If you do not, when the pressure increases, the safety valve may activate and discharge water.

A*

A*

A

KC

KR

KRB

Fig. 2 Filler cock

(A*) option.

«
...
13
14
15
16
17
...
»

Содержание minorca kr

































































Отзывы:

Нет отзывов

Похожие инструкции для minorca kr

Бренд: Vaillant Страницы: 12

Calyadra comfort

Бренд: C&M Страницы: 12

Бренд: Ikon Страницы: 16

Бренд: Riello Страницы: 196

Super Xpress SX iQ Series

Бренд: OSO HOTWATER Страницы: 28

Electric Smokeless Broiler

Бренд: Saladmaster Страницы: 12

CompactGas 1000

Бренд: Hoval Страницы: 34

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 62

Бренд: A.O. Smith Страницы: 76

ATLAS D 32 CONDENS K130 UNIT

Бренд: Ferroli Страницы: 80

ATLAS D 25 SI UNIT

Бренд: Ferroli Страницы: 96

Бренд: Market Forge Industries Страницы: 16

Бренд: Raypak Страницы: 8

Бренд: Dunkirk Страницы: 36

Бренд: Sime Страницы: 128

Бренд: Vaillant Страницы: 40

Brava One HE 40 ErP

Бренд: Sime Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды