Fondital minorca kr Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

32

Instructions for the installer

3.6 Air intake and flue gas venting system

Flue gas discharge into the atmosphere and air intake/flue gas venting systems must comply with applicable laws and standards in the
country of installation that are considered as fully transcribed herein.

DANGER

The boiler is equipped with a safety device for flue gas exhaustion check.
It is strictly forbidden to tamper with and/or prevent operation of such safety device.
Should an air/flue gas system malfunction occur, the device will shut-down the boiler by interrupting the gas supply to the boiler

and the LCD will display the E03 code.

In this case it is necessary to have safety device, boiler and the air intake/flue gas venting ducts promptly checked by a service

centre or a qualified service engineer.

In case of repeated stops, it is necessary to have safety device, boiler and the air intake/flue gas venting ducts checked by a service

centre or a qualified service engineer.

After each operation on the safety device or the air suction/flue gas exhaust system, it is necessary to perform a functional test of

the boiler.

In case it is necessary to replace the safety device use only original spare parts supplied by the Manufacturer.
To reset the combustion gas exhaust control device operation it is necessary to press "Reset".

DANGER

For the air intake/flue gas venting systems, specific, manufacturer approved, condensate acid-resistant pipes and systems must be

used, suitable for condensing boilers.

DANGER

Flue gas venting pipes are to be installed tilted toward the boiler so that condensate runs toward the combustion chamber, which

is designed for condensate collection and drainage.

Should the above procedure not be possible, it is necessary to install, in condensate stagnation areas, devices designed for

condensate collection and conveying to the condensate drain system.

It is necessary to avoid formation of condensate stagnation areas in the flue gas venting system, with the exception of the

condensate trap possibly connected to the venting system itself.

The manufacturer cannot be held responsible for any damage caused by inappropriate boiler installation or operation, modification to the
boiler, or due to non-observance of the instructions provided by the manufacturer or of legislation and standards applicable for the materials
installed.

Fig. 9 Installation examples

KEY
A

Air intake

S

Flue gas vent

Condensate
Rain

«
...
30
31
32
33
34
...
»

Содержание minorca kr

































































Отзывы:

Нет отзывов

Похожие инструкции для minorca kr

Бренд: Crown Boiler Страницы: 54

Бренд: ideal commercial Страницы: 6

Бренд: Main Heating Страницы: 83

Бренд: Unical Страницы: 40

Бренд: New Yorker Страницы: 44

Бренд: Garland Страницы: 2

Бренд: Vaillant Страницы: 76

Бренд: Zojirushi Страницы: 40

Бренд: Glow-worm Страницы: 12

Бренд: Beretta Страницы: 144

Бренд: Camus Hydronics Страницы: 90

Бренд: Riello Страницы: 75

Centora green 24 Nat

Бренд: Chaffoteaux & Maury Страницы: 24

Бренд: Bryan Boilers Страницы: 85

Бренд: Viessmann Страницы: 192

Ultra-Max Lava Rock Gas Char-Broilers 8024CB

Бренд: Star Manufacturing Страницы: 2

Star-Max Lava Rock Gas Char-Broilers 6015CBD

Бренд: Star Manufacturing Страницы: 2

Бренд: Star Manufacturing Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды