Fondital MADEIRA SOLAR KRBS 12 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 96

background image

27

Instructions for the user

1.15.1 Burner shut-down

Fault code

E01

is displayed lashing on the display in the event of burner shut-down due to missing lame.

If this happens, proceed as follows:

•

check that the gas cock is open and light a kitchen gas ring for example to check the gas supply;

•

once having checked if the fuel is available, press the

button to restore burner operation: if, after two starting attempts, the boiler

still fails to start and enters the shut-down mode again, contact a service centre or qualiied personnel for maintenance.

WARNING

If the burner shuts down frequently, there is a recurring malfunction, so contact a service centre or a qualified service engineer.

1.15.2 Shut-down due to incorrect air/flue gas system draught

The boiler is equipped with a safety device for lue gas exhaustion check.
Should an air/lue gas system malfunction occur, the control device will shut-down the boiler by interrupting the gas supply to the boiler and
the LCD will display the

E03

code.

In this case, contact a Service Centre or a qualiied service engineer to carry out the maintenance.

1.15.3 Shut-down due to low water pressure

If "shutdown due to insuicient pressure in system" error

E04

starts lashing (indicating safety water pressure switch triggering), ill the system

by opening the iller cock as shown in Fig. 3 Filler cock.

E04

error is displayed when system pressure drops below 0.4 bar and error will be

automatically reset as soon as system pressure reaches 1.0 bar. Water pressure must be 1-1.3 bars while the boiler is cold.
In order to restore water pressure, proceed as follows:

•

turn the iller cock Fig. 3 Filler cock anticlockwise to allow water to enter the boiler;

•

keep the cock open until the control panel shows a value of 1÷1.3 bar;

•

turn cock clockwise to close it.

If the boiler still fails to operate, contact a service centre or a qualiied service engineer.

DANGER

Make sure you close the cock carefully after filling. If you do not, when the pressure increases, error E09 may be displayed and the

heating system safety valve may activate and discharge water.

A

Fig. 3 Filler cock

PDF Compressor Pro

«
...
25
26
27
28
29
...
»

Содержание MADEIRA SOLAR KRBS 12

































































































Отзывы:

Нет отзывов

Похожие инструкции для MADEIRA SOLAR KRBS 12

Vela X N 24 MB/IT

Бренд: Lamborghini Caloreclima Страницы: 30

Бренд: Noritz Страницы: 38

Бренд: Vaillant Страницы: 52

MagnaTech BMGH1600

Бренд: Brute Страницы: 116

Бренд: Halstead Страницы: 20

Бренд: Hamworthy Страницы: 48

BRITONY System II 100

Бренд: C&M Страницы: 12

Бренд: Centrometal Страницы: 40

Бренд: Biodom Страницы: 61

Бренд: Burnham Страницы: 12

Бренд: Burnham Страницы: 104

Бренд: Tilia Страницы: 24

Бренд: Immergas Страницы: 48

Бренд: Truma Страницы: 12

Бренд: ETERNITY Страницы: 28

Osprey 2 CFL 125

Бренд: Potterton Страницы: 28

Vitocell-B 100 CVB Series

Бренд: Viessmann Страницы: 24

Бренд: Rinnai Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды