background image

2

IMPORTANT SAFETY INSTRUCTIONS

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with dry cloth.
7.  Do  not  block  any  ventilation  openings.  Install  in  accordance  with  the  manufacturer’s 

instructions.

8.  Do  not  install  near  any  heat  sources  such  as  radiators,  heat  registers,  stoves,  or  other 

apparatus (including amplifiers) that produce heat.

9.  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has 

two blades with one wider than the other. A grounding type plug has two blades and a third 

grounding prong. The wide blade or the third prong are provided for your safety. If the provided 

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.  Protect the power cord from being walked on or pinched particularly at plugs, convenience 

receptacles, and the point where they exit from the apparatus.

11.  Only use attachments/accessories specified by the manufacturer.
12. 

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, 

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over. 

13.  Unplug this apparatus during lightning storms or when unused for long periods of time.
14.  Refer all servicing to qualified service personnel. Servicing is required when the apparatus 

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has 

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain 

or moisture, does not operate normally, or has been dropped. 

15.  No naked flames, such as lighted candles, should be placed on the apparatus.

The  appliance  coupler  is  used  as  the  disconnect  device,  the  disconnect  device  shall  remain  readily 

operable.

Do not use a damaged or frayed power cord.

If the mains plug supplying the apparatus incorporates a fuse then it should only be replaced with a fuse 

of identical or lower rupture value.

 

    The apparatus shall be connected to a mains socket outlet with a protective earthing connection.

 

   Laite on liitettävä suojamaadoituskoskettimilla va rustettuumpistorasiaan

 

   Apparatet må tikoples jordet stikkontakt

 

   Apparaten skall anslutas till jordat uttag

GB

FIN

NOR
SWE

Содержание RedNet 3

















Отзывы: