background image

www.fmiproducts.com

54010F

5

FIREPLACE INSTALLATION

Continued

5.  Before securing fireplace to prepared 

framing, ember protector (provided) must 
be placed between hearth extension (not 
supplied) and under bottom front edge 
of  fireplace to protect against glowing 
embers falling through. If fireplace is to 
be installed on a raised platform, a Z-type 
ember protector (not supplied) must be 
fabricated to fit your required platform 
height. Ember protector should extend 
under fireplace a minimum of 1". Ember 
protector should be made of galvanized 
sheet metal (28 gauge minimum) to pre-
vent corrosion (see Figure 5).

6.  Using screws or nails, secure fireplace to 

the framing through flanges located on 
sides of the fireplace (see Figure 4).

Figure 5 - Hearth Extensions

Figure 4 - Nailing Flanges

HEARTH EXTENSION

A hearth extension is required to protect com-
bustible floor constructed in front of fireplace. 
The hearth extension is not included and must 
be fabricated, The hearth extension must 
project at lease 12" one side and 20" on other 
side of fireplace opening.
Hearth extension must be made of noncom-
bustible, inorganic material having an effective 
thermal conductivity of K=0.84 BTU IN/FT, 
HR. F (or less) at 1" thick. 
Thermal conductivity "K" of materials can 
be obtained from manufacturer or supplier 
of noncombustible material. The minimum 
required thickness ofr any material could be 
obtained by the following formula:
K factor at 1" = thickness required
     0.84

For example, if the material selected has a K 
factor of 0.25, such as glass fiber, the following 
formula would apply:
 

0.25 x 1.0" = 0.30" thickness required

 0.84
If hearth extension is to be covered, use non-
combustible material such as tile, slate, brick, 
concrete, metal, glass, marble, stone, etc.
Provide a means to prevent hearth extension 
from shifting and seal gap between fireplace 
frame and hearth extension with non-combus-
tible material (see Figure 5).

 WARNING: Hearth extension is 

to be installed only as described.

MANTEL CLEARANCES

Woodwork such as wood trims, mantels or 
any other combustible material must not be 
placed at least 9" above opening of fireplace 
(see Figure 6, page 6).
Combustible materials above 9" and projecting 
more than 1 

1

/

2

" from the fireplace front face 

must not be at least 12" above fireplace opening 
(NFPA STD 211, Sec. 7-3.3.3).
Mantels or any other combustible material 
may also come up to the side edge of the 
black metal face of the fireplace. Clearances 
from side of fireplace to any combustible 
material and wall should fall within the limits 
show in Figure 7, page 6.

Nailing 
Flange

Nail or 
Screw

Seal Cap

Do Not Block Louver

Seal Cap

Ember 
Protector

Ember Protector

Hearth 
Extension

Hearth 
Extension

Содержание 36L Series





















Отзывы: